Loading ...

Superior corrosion resistance to harsh chemicals found in common household cleaning and plumbing repair products, Won t work harden even with repeated bending, Greater strength & flexibility. The patented polymer braid exhibits greater elasticity than stainless steel braiding, significantly increasing the flexibility of the connector, No kinking, no crimping. The polymer braided jacket is specially engineered to bend freely without kinking or crimping the connector, Available for PEX connections, No dielectric union needed with installation as the braiding and rubber are constructed of non-conductive materials, Less torque to seal against the pliable rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and offer a better seal, For use in exposed locations only to connect water heaters and other water connected devices to the water supply. 100% Compliant, Not intended for use with recirculating water systems that produce continuous use temperatures above 115 F.
Superior corrosion resistance to harsh chemicals found in common household cleaning and plumbing repair products, Won t work harden even with repeated bending, Greater strength & flexibility. The patented polymer braid exhibits greater elasticity than stainless steel braiding, significantly increasing the flexibility of the connector, No kinking, no crimping. The polymer braided jacket is specially engineered to bend freely without kinking or crimping the connector, Available for PEX connections, No dielectric union needed with installation as the braiding and rubber are constructed of non-conductive materials, Less torque to seal against the pliable rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and offer a better seal, For use in exposed locations only to connect water heaters and other water connected devices to the water supply. 100% Compliant, Not intended for use with recirculating water systems that produce continuous use temperatures above 115 F.
Superior corrosion resistance to harsh chemicals found in common household cleaning and plumbing repair products, Won t work harden even with repeated bending, Greater strength & flexibility. The patented polymer braid exhibits greater elasticity than stainless steel braiding, significantly increasing the flexibility of the connector, No kinking, no crimping. The polymer braided jacket is specially engineered to bend freely without kinking or crimping the connector, Available for PEX connections, No dielectric union needed with installation as the braiding and rubber are constructed of non-conductive materials, Less torque to seal against the pliable rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and offer a better seal, For use in exposed locations only to connect water heaters and other water connected devices to the water supply. 100% Compliant, Not intended for use with recirculating water systems that produce continuous use temperatures above 115 F.
Superior corrosion resistance to harsh chemicals found in common household cleaning and plumbing repair products, Greater strength & flexibility. The patented polymer braid exhibits greater elasticity than stainless steel braining, significantly increasing the flexibility of the connector, No kinking, No crimping. The polymer braided jacket is specially engineered to bend freely without kinking or crimping the connector, Won t work harden even with repeated bending, No dielectric union needed with installation as the braiding and rubber are constructed of non-conductive materials, Less torque to seal against the pliable Nitrile rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and offer a better seal, 100% compliant to California and Vermont low-lead requirements, For use in exposed locations only to connect water heaters and other water connected devices to the water supply., Not intended for use with recirculating water systems that produce continuous use temperatures above 115 F.
1/2 FIP X 1/2 MIP ADAPTER
Locke Part #: H0665MFG Part #: 120-8X
26613146249
Product Image Not Available 1/2 Flare x 7/8 Ballcock Nut 12 in
Locke Part #: B0322MFG Part #: BF3-12DL F
Engineered polymer braided fibers bend freely without kinking or Crimping, Reinforced PVC inner hose ensures durability, No Lead, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, For use in potable water distribution systems in accessible locations only., 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections 26613966595
1/2 in Flare x 1/2 FIP 20 in
Locke Part #: B0321MFG Part #: BF3-20A F
Engineered polymer braided fibers bend freely without kinking or Crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, No Lead, For use in potable water distribution systems in accessible locations only. 26613966724
1/2 NOM BRBX 3/8"OD STRVLV PX TBING
Locke Part #: B0304MFG Part #: BRPX14X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, No Lead, PEX end designed to ASTM F1807, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems using ASTM F1807, and/or F2098 connection methods, Knurled oval handle provides a secure grip and smooth on/off operation,, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613142326
1/2 NOM COMP X 3/8 OD X 1/4 OD OFFSET 180 RGH
Locke Part #: B0448MFG Part #: CR1900DVSX R
Independent flow control. Dual outlet, dual shut-off operation permits you to shut-off water flow to one fixture while maintaining water flow to another fixture, Code approved replacement where separate shut-offs are required for two lines, Knurled oval handle provides a secure grip and smooth on/off operation, Straight inlet to outlet design (same-side outlets) is great for installations in tight spaces, Machined one-piece brass body provides strength, durability, and long-lasting performance, For use with water in accessible locations only., Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, 100% compliant product available,, Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613137971
Compatible with PEX, copper, and CPVC., Compact machined one-piece body design, Pre-inserted tube stiffener is installation ready for a faster connection, Fast, reliable, secure, Smooth 1/4 turn operation, 100% leak tested, 100% Compliant, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613142128
Compatible with PEX, copper, and CPVC., Compact machined one-piece body design, Pre-inserted tube stiffener is installation ready for a faster connection, Fast, reliable, secure, Smooth 1/4 turn operation, 100% leak tested, 100% Compliant, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613142142
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613135380
1/2" FIP X 1/2" FIP 12" FAUCET
Locke Part #: B0212MFG Part #: S8-12A F
Engineered polymer braided fibers bend freely without kinking or crimping, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection,, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, Reinforced PVC inner hose ensures durability, 100% No Lead For use in potable water distribution systems in accessible locations only 26613008868
1/2" FIP X 1/2" FIP 16" FAUCET
Locke Part #: B0213MFG Part #: S8-16A F
Engineered polymer braided fibers bend freely without kinking or crimping, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection,, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, Reinforced PVC inner hose ensures durability, 100% No Lead For use in potable water distribution systems in accessible locations only 26613008882
1/2" FIP X 1/2" FIP 20" FAUCET
Locke Part #: B0214MFG Part #: S8-20A F
Engineered polymer braided fibers bend freely without kinking or crimping, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection,, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, Reinforced PVC inner hose ensures durability, 100% No Lead For use in potable water distribution systems in accessible locations only 26613008905
1/2"NOM BRB X 3/8"OD ANGVA
Locke Part #: B0329MFG Part #: KTBRPX19X C
Precision-machined brass ball is specially engineered and mated with PTFE seats to provide smooth operation without freeze ups even after long periods of non-use, TWO high-performance O-rings withstand high temperatures and corrosion from harsh water environments, Machined one-piece brass body provides strength, durability, and long-lasting performance, Brass stem is assembled from the inside out with two O-rings to ensure safe, reliable performance, Plated stem provides corrosion resistance and prevents O-ring damage after long periods of non-use, Patented, chrome plated metal handle is designed for durability, corrosion resistance, and a sleek appearance, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, 100% leak tested, 100% Compliant product available, For use in potable water distribution systems 26613150062
1/2"NOM BRB X 3/8"OD STRVAL
Locke Part #: B0330MFG Part #: KTBRPX14X C
26613150055
1/2"NOM BRBX 3/8 OD ANGVLV PX TBING
Locke Part #: B0303MFG Part #: BRPX19X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, No Lead, PEX end designed to ASTM F1807, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems using ASTM F1807, and/or F2098 connection methods, Knurled oval handle provides a secure grip and smooth on/off operation,, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613138206
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Long wing nuts allow for quick connection and ensure dependable thread engagement, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613966823
1/2-in Flare Nut
Locke Part #: H0508MFG Part #: 141S-8
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared. 26613005744
1/2-in OD Flare x 1/2-in FIP Adaptor
Locke Part #: H0518MFG Part #: 46-8-8
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005270
1/2-in OD Flare x 1/2-in MIP Adaptor
Locke Part #: H0538MFG Part #: 48-8-8
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005430
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005041
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005140
1/2-in OD Flare x 3/4-in FIP Adaptor
Locke Part #: H0519MFG Part #: 46-8-12
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005287
1/2-in OD Flare x 3/4-in MIP Adaptor
Locke Part #: H0539MFG Part #: 48-8-12
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005447
1/2-in OD Short Flare Nut
Locke Part #: H0502MFG Part #: 41S-8
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613004990
1/2-in OD Tube Sleeves
Locke Part #: H0577MFG Part #: 60-8
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing. 26613005966
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613135533
1/4 TRN ANG VLV 1/2 NOM X 3/8 CMP
Locke Part #: B0266MFG Part #: G2CR19X C
One-piece shut-off mechanism provides smooth on-off operation without freeze ups even after long periods of non-use, Positive 1/4 turn shut off, Full-flow operation with no waterway obstructions, Corrosion-resistant handle is plated in an attractive chrome finish, 100% Leak tested, No Lead, Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental operation during rough-ins, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems (parts containing PX and PXX only), Not intended for recirculating water systems that produce continuous use temperatures above 115 F., For use in ASTM F877 water distribution systems as noted in Appendixes (parts containing PX and PXX only), For use in potable water distribution systems. 26613135069
1/4 TURN ANG VLV 1/2 FIP X 3/8 CMP CP
Locke Part #: B0268MFG Part #: G2R17X C
One-Piece shut-off mechanism provides smooth on-off operation without freeze ups even after long periods of non-use, Positive 1/4 turn shut-off, Full-flow operation with no waterway obstructions, Corrosion-resistant handle is plated in an attractive chrome finish, 100% leak tested, Machined one-piece brass body provides strength, durability and long-lasting performance, Easy-to-remove handle with screw attachment protects accidental operation during rough-ins, Compliant G2 Stops available for California and Vermont no-lead Requirements, For use in potable water distribution systems., Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613137926
Precision-machined brass ball is specially engineered and mated with PTFE seats to provide smooth operation without freeze ups even after long periods of non-use, Two high-performance O-rings withstand high temperatures and corrosion from harsh water environments, Machined, extruded brass body provides strength, durability, and long-lasting performance, Blow-out-proof brass stem is assembled from the inside out with two O-rings to ensure safe, reliable performance, Plated stem provides corrosion resistance and prevents o-ring damage after long periods of non-use, Exclusive, chrome-plated metal handle is designed for durability, corrosion resistance, & a sleek appearance, Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, 100% leak tested, 100% compliant product available, For use with water in accessible locations only.
One-piece shut-off mechanism provides smooth on-off operation without freeze ups even after long periods of non-use, 100% Leak tested, No Lead, Corrosion-resistant handle is plated in an attractive chrome finish, Positive 1/4 turn shut off, Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental operation during rough-ins, PEX end designed to ASTM F1960, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F.
One-piece shut-off mechanism provides smooth on-off operation without freeze ups even after long periods of non-use, Positive 1/4 turn shut off, Full-flow operation with no waterway obstructions, Corrosion-resistant handle is plated in an attractive chrome finish, 100% Leak tested, No Lead, Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental operation during rough-ins, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems (parts containing PX and PXX only), Not intended for recirculating water systems that produce continuous use temperatures above 115 F., For use in ASTM F877 water distribution systems as noted in Appendixes (parts containing PX and PXX only), For use in potable water distribution systems.
One-piece shut-off mechanism provides smooth on-off operation without freeze ups even after long periods of non-use, Positive 1/4 turn shut-off, Full-flow operation with no waterway obstructions, Corrosion-resistant handle is plated in an attractive chrome finish, Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental operation during rough-ins, 100% leak tested, 100% Compliant product available, For use with water in accessible locations only., Not intended for recirculating water systems that produce continuous use temperatures above 115 F.
1/4 TURN STR VLV 1/2 NOM X 3/8 CMP CP
Locke Part #: B0267MFG Part #: G2CR14X C
One-Piece shut-off mechanism provides smooth on-off operation without freeze ups even after long periods of non-use, Positive 1/4 turn shut off, Full-flow operation with no waterway obstructions, Corrosion-resistant handle is plated in an attractive chrome finish, Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental operation during rough-ins, 100% Leak tested, No Lead, For use in potable water distribution systems. Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613136929
Precision-machined brass ball is specially engineered and mated with PTFE seats to provide smooth operation without freeze ups even after long periods of non-use, TWO high-performance o-rings withstand high temperatures and corrosion from harsh water environments, 100% leak tested, Machined one-piece brass body provides strength, durability and long-lasting performance, Blow-out proof brass stem is assembled from the inside out with two o-rings to ensure safe, reliable performance, Plated stem provides corrosion resistance and prevents o-ring damage after long periods of non-use, Patented, chrome plated metal handle is designed for durability, corrosion resistance & a sleek appearance, Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, Compliant KT Stops available for California and Vermont low-lead requirements, For use in potable water distribution systems
Precision-machined brass ball is specially engineered and mated with PTFE seats to provide smooth operation without freeze ups even after long periods of non-use, Two high-performance o-rings withstand high temperatures and corrosion from harsh water environments, Machined one-piece brass body provides strength, durability, and long-lasting performance, Brass stem is assembled from the inside out with two o-rings to ensure safe, reliable performance, Plated stem provides corrosion resistance and prevents o-ring damage after long periods of non-use, Exclusive, plated metal handle is designed for durability, corrosion resistance, and a sleek appearance, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, 100% Leak tested. No Lead, For use with water in accessible locations only.
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements., For use with instrumentation, hydraulic and pneumatic systems. Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
1/4-in Compression Cap
Locke Part #: H0574MFG Part #: 61CP-4X
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613154411
1/4-in Compression Sleeves
Locke Part #: H0575MFG Part #: 60-4
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing. 26613005928
1/4-in Flare Nut
Locke Part #: H0506MFG Part #: 141S-4
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared. 26613005720
1/4-in OD Flare Cap
Locke Part #: H0490MFG Part #: 40-4
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines, Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613004914
1/4-in OD Flare x 1/4-in MIP Adaptor
Locke Part #: H0528MFG Part #: 48-4-4
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005348
26613005010
1/4-in OD Short Flare Nut
Locke Part #: H0500MFG Part #: 41S-4
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613004952
1/4-in OD Tube Compression Union
Locke Part #: H0620MFG Part #: 62-4X
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613135403
1/4-in OD Tube Nut
Locke Part #: H0570MFG Part #: 61-4
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613006055
For use with PEX, vinyl and polyethylene tubing in potable water distribution systems, Not intended for use with steel, copper or aluminum tubing 26613005997
026613155265
Product Image Not Available 3/4 Female Hose Adaptors (FIP End)
Locke Part #: H0652MFG Part #: HU11-12-12X
26613149813
Product Image Not Available 3/4 Female Swivel Hose Adaptors (FIP End)
Locke Part #: H0645MFG Part #: HUS11-12-12X
For use with residential and commercial grade garden hose., All female hose thread connections require a rubber washer (sold separately) inserted prior to installation 26613137698
Product Image Not Available 3/4 Male Hose Adaptors (MIP End)
Locke Part #: H0651MFG Part #: HU22-12-12TPX
For use with residential and commercial grade garden hose., All female hose thread connections require a rubber washer (sold separately) inserted prior to installation 26613149998
3/4FIP X 3/4FIP X12 COPPER WHC
Locke Part #: L0958MFG Part #: WB00-12N
Superior galvanic corrosion resistance. Patented internal dielectric sleeve effectively isolates dissimilar metals within the waterway to prevent galvanic corrosion, No dielectric union needed with installation. Dielectric is built-in to the design of the connector, Less torque to seal against the pliable rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and a better seal, For use in exposed locations only to connect water heaters and other water connected devices to the water supply, 100% Compliant (WB00 only) 26613089287
3/4FIP X 3/4PEX X18 COPPER WHC
Locke Part #: L0008MFG Part #: WB07-18
Patented Internal Dielectric Sleeve, No Dielectric Union Needed, Less Torque to Seal, Longer Connector Nuts, Available for PEX connection 26613048871
3/4FIP X 3/4PEX X24 COPPER WHC
Locke Part #: L0006MFG Part #: WB07-24
Patented Internal Dielectric Sleeve, No Dielectric Union Needed, Less Torque to Seal, Longer Connector Nuts, Available for PEX connection 26613100661
3/4FIP X3/4NOM M/FSWT X12 CPR
Locke Part #: L0009MFG Part #: WB034-12N
Superior galvanic corrosion resistance. Patented internal dielectric sleeve effectively isolates dissimilar metals within the waterway to prevent galvanic corrosion, No dielectric union needed with installation. Dielectric is built-in to the design of the connector, Less torque to seal against the pliable Nitrile rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and a better seal, 100% compliant to California, Vermont and Maryland low-lead requirements, For use in exposed locations only to connect water heaters and other water connected devices to the water supply 26613089409
3/4FIP X3/4NOM M/FSWT X18 CPR
Locke Part #: L0011MFG Part #: WB034-18N
Superior galvanic corrosion resistance. Patented internal dielectric sleeve effectively isolates dissimilar metals within the waterway to prevent galvanic corrosion, No dielectric union needed with installation. Dielectric is built-in to the design of the connector, Less torque to seal against the pliable Nitrile rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and a better seal, 100% compliant to California, Vermont and Maryland low-lead requirements, For use in exposed locations only to connect water heaters and other water connected devices to the water supply 26613089423
3/4FIP X3/4NOM M/FSWT X24 CPR
Locke Part #: L0012MFG Part #: WB034-24N
Superior galvanic corrosion resistance. Patented internal dielectric sleeve effectively isolates dissimilar metals within the waterway to prevent galvanic corrosion, No dielectric union needed with installation. Dielectric is built-in to the design of the connector, Less torque to seal against the pliable Nitrile rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and a better seal, 100% compliant to California, Vermont and Maryland low-lead requirements, For use in exposed locations only to connect water heaters and other water connected devices to the water supply 26613093710
3/8 CMP X 1/2 FIP X 30" FAUCET
Locke Part #: B0299MFG Part #: S1-30A F
Engineered polymer braided fibers bend freely without kinking or Crimping, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Reinforced PVC inner hose ensures durability, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613158730
3/8 CMP X 3/8 CMP X 16" DISH
Locke Part #: B0210MFG Part #: S1-16DW F
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613158815
3/8 CMP X 3/8 CMP X 20" DISH
Locke Part #: B0211MFG Part #: S1-20DW F
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613158839
Product Image Not Available 3/8 Flare x 7/8 Ballcock Nut 12 in
Locke Part #: B0318MFG Part #: BF1-12DL F
Engineered polymer braided fibers bend freely without kinking or Crimping, Reinforced PVC inner hose ensures durability, No Lead, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, For use in potable water distribution systems in accessible locations only., 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections 26613966427
3/8 OD Fine Thread Flare Caps
Locke Part #: H0636MFG Part #: FC-6
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613059037
26613004808
26613006772
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613136615
26613004778
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613135526
26613136325
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613136646
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, For use with instrumentation, hydraulic and pneumatic systems., Compliant to California, Vermont and Maryland low-lead requirements, Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing,, Compliant product CSA approved to California Health & Safety Code 116875,Vermont Bill S.152 and Maryland House Bill 372 (Project # 234795) 26613140933
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, For use with instrumentation, hydraulic and pneumatic systems., Compliant to California, Vermont and Maryland low-lead requirements, Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing,, Compliant product CSA approved to California Health & Safety Code 116875,Vermont Bill S.152 and Maryland House Bill 372 (Project # 234795) 26613140926
3/8" COMP X 3/8" COMP 12" DWSH
Locke Part #: B0209MFG Part #: S1-12DW F
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613144665
3/8" COMP X 7/8" BALLCOCK
Locke Part #: B0282MFG Part #: S1-12DLM F
26613157023
3/8" COMP X 7/8" BALLCOCK
Locke Part #: B0283MFG Part #: S1-16DLM F
26613160276
3/8" COMP X 7/8" BALLCOCK
Locke Part #: B0289MFG Part #: S1-16DL F
Engineered polymer braided fibers bend freely without kinking or crimping, 100% No Lead, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Long wing nuts allow for quick connection and ensure dependable thread engagement, For use in potable water distribution systems in accessible locations only, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections 26613095370
3/8" COMP X 7/8" BALLCOCK
Locke Part #: B0298MFG Part #: S1-12DL F
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Long wing nuts allow for quick connection and ensure dependable thread engagement, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613009049
3/8" COMP X 7/8" BALLCOCK
Locke Part #: B0302MFG Part #: S1-20DL F
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Long wing nuts allow for quick connection and ensure dependable thread engagement, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613009063
3/8" COMP X FIP, 12" FAUCET
Locke Part #: B0294MFG Part #: S1-12A F
Engineered polymer braided fibers bend freely without kinking or Crimping, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Reinforced PVC inner hose ensures durability, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613008806
3/8" COMP X FIP, 16" FAUCET
Locke Part #: B0295MFG Part #: S1-16A F
Engineered polymer braided fibers bend freely without kinking or Crimping, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Reinforced PVC inner hose ensures durability, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613008820
3/8" COMP X FIP, 20" FAUCET
Locke Part #: B0296MFG Part #: S1-20A F
Engineered polymer braided fibers bend freely without kinking or Crimping, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Reinforced PVC inner hose ensures durability, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only 26613008844
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements., For use with instrumentation, hydraulic and pneumatic systems. Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements., For use with instrumentation, hydraulic and pneumatic systems. Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
3/8" OD Tube x 1/2" F.I.P Reducing Elbow
Locke Part #: H0661MFG Part #: 70-6-8 X
026613148809
3/8-in Compression Sleeves
Locke Part #: H0576MFG Part #: 60-6
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing. 26613005942
3/8-in Flare Nut
Locke Part #: H0507MFG Part #: 141S-6
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared. 26613005737
Engineered polymer braided fibers bend freely without kinking or Crimping, Reinforced PVC inner hose ensures durability, No Lead, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, For use in potable water distribution systems in accessible locations only., 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections 26613966687
3/8-in OD Flare Cap
Locke Part #: H0491MFG Part #: 40-6
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines, Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613004921
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005232
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005393
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005379
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005249
3/8-in OD Flare x 3/4-in MIP Adaptor
Locke Part #: H0534MFG Part #: 48-6-12
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005409
3/8-in OD Flare x 3/8-in MIP Adaptor
Locke Part #: H0532MFG Part #: 48-6-6
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005386
Recommended for higher pressures than those covered by compression fittings,Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005522
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005034
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005133
3/8-in OD Short Flare Nut
Locke Part #: H0501MFG Part #: 41S-6X
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613058900
3/8-in OD Tube Compression Union
Locke Part #: H0621MFG Part #: 62-6X
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613136899
3/8-in OD Tube Nut
Locke Part #: H0571MFG Part #: 61-6
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613006079
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613135427
3/8CMPX3/8CMP 20" FCET KC NOSE
Locke Part #: B0305MFG Part #: S1-20KC F
Engineered polymer braided fibers bend freely without kinking or Crimping, Reinforced PVC inner hose ensures durability, No Lead, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, For use in potable water distribution systems in accessible locations only., 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections 26613158914
3/8CMPX3/8CMPX12" FCET KC NOSE
Locke Part #: B0297MFG Part #: S1-12KC F
Engineered polymer braided fibers bend freely without kinking or Crimping, Reinforced PVC inner hose ensures durability, No Lead, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, For use in potable water distribution systems in accessible locations only., 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections 26613158907
5/8 OD Compression Tee
Locke Part #: H0633MFG Part #: 64-10X
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613135311
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements., For use with instrumentation, hydraulic and pneumatic systems. Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
5/8-in Compression Sleeves
Locke Part #: H0578MFG Part #: 60-10
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing. 26613005973
5/8-in Flare Nut
Locke Part #: H0509MFG Part #: 141S-10
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared. 26613005751
5/8-in OD Flare Cap
Locke Part #: H0493MFG Part #: 40-10
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines, Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613004945
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005300
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005461
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005317
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005478
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005058
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005157
5/8-in OD Short Flare Nut
Locke Part #: H0503MFG Part #: 41S-10
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005003
5/8-in OD Tube Compression Union
Locke Part #: H0623MFG Part #: 62-10X
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613136783
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements., For use with instrumentation, hydraulic and pneumatic systems. Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613148144
7/8" OD Flare x 3/4" F.I.P Adapter
Locke Part #: H0524MFG Part #: 46-14-12 X
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Superior galvanic corrosion resistance. Patented internal dielectric sleeve effectively isolates dissimilar metals within the waterway to prevent galvanic corrosion, No dielectric union needed with installation. Dielectric is built-in to the design of the connector, Less torque to seal against the pliable rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and a better seal, For use in exposed locations only to connect water heaters and other water connected devices to the water supply, 100% Compliant (WB00 only)
Superior galvanic corrosion resistance. Patented internal dielectric sleeve effectively isolates dissimilar metals within the waterway to prevent galvanic corrosion, No dielectric union needed with installation. Dielectric is built-in to the design of the connector, Less torque to seal against the pliable rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and a better seal, For use in exposed locations only to connect water heaters and other water connected devices to the water supply, 100% Compliant (WB00 only)
7/8-in OD Flare x 3/4-in MIP Adaptor
Locke Part #: H0546MFG Part #: 48-14-12
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared 26613005485
7/8-in OD Tube Compression Union
Locke Part #: H0626MFG Part #: 62-14X
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613136806
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation. Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing 26613135366
Replaces most old style fill valves, Adjusts from 9 to 14 inches in height, Features 1/4-turn height adjustment, Includes metal S clip, plastic refill tube, plastic lock nut, plastic fill valve connector nut, rubber cone washer, and rubber shank washer boxed
ANG VAL 1/2 CMP X 1/4 CMP RIS
Locke Part #: B0239MFG Part #: OCR09X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, For use in ASTM F877 water distribution systems as noted in Appendixes (parts containing PX and PXX only), For use in potable water distribution systems. Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613135274
ANG VAL 1/2 CMP X 3/8 CMP
Locke Part #: B0332MFG Part #: SCR19X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, Large loose key handle provides a secure grip for trouble-free on/off operation, Removable loose key handle helps protect against accidental stop operation during rough-ins, No Lead, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems (parts containing PX and PXX only), For use in ASTM F877 water distribution systems as noted in Appendixes (parts containing PX and PXX only), For use in potable water distribution systems, Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613137438
ANG VAL 1/2 FIP X 3/8 CMP RIS
Locke Part #: B0225MFG Part #: OR17X C
Machined one-piece brass body provides strength, durability and long-lasting performance, Oval knurled handle provides a secure grip and smooth on/off operation, Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, Compliant Stops available for California and Vermont low-lead requirements, For use in potable water distribution systems. Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613138176
ANG VAL 1/2 NOM CMP X 3/8 CMP
Locke Part #: B0226MFG Part #: OCR19X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, For use in ASTM F877 water distribution systems as noted in Appendixes (parts containing PX and PXX only), For use in potable water distribution systems. Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613135113
ANG VAL 1/2 SWT X 3/8 CMP RIS
Locke Part #: B0231MFG Part #: R19X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, Oval knurled handle provides a secure grip and smooth on/off operation, Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, No Lead, For use with water in accessible locations only., Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613138480
ANG VLV 1/2 NOM CMP X 3/8 OD
Locke Part #: B0237MFG Part #: KTCR19X C
Precision-machined brass ball is specially engineered and mated with PTFE seats to provide smooth operation without freeze ups even after long periods of non-use, TWO high-performance o-rings withstand high temperatures and corrosion from harsh water environments, Machined one-piece brass body provides strength, durability and long-lasting performance, Blow-out proof brass stem is assembled from the inside out with two o-rings to ensure safe, reliable performance, Plated stem provides corrosion resistance and prevents o-ring damage after long periods of non-use, Patented, chrome plated metal handle is designed for durability, corrosion resistance & a sleek appearance, Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, 100% leak tested, Compliant KT Stops available for California and Vermont low-lead requirements, For use in potable water distribution systems 26613138688
Brass Insert For 1/4" OD Plastic Tubing
Locke Part #: M0036MFG Part #: 63PT-4 X
Available in a broad range of sizes and styles, Fitting does not require any flaring, soldering, or other type of tubing preparation, No Lead, For use in potable water, instrumentation, hydraulic, and pneumatic systems., For use with plastic tubing in potable water distribution systems. Not intended for use with non-plastic tubing.
CLO RIS 3/8 OD X 20 LG
Locke Part #: C0235MFG Part #: P1-20DL
One-piece construction, Cut-to-Length for a clean, professional installation, 100% Compliant to California and Vermont low-lead requirements, For use in potable water distribution systems in accessible locations only 26613044934
CLO RIS 3/8"OD X 12"
Locke Part #: C0234MFG Part #: P1-12DL
One-piece construction, Cut-to-Length for a clean, professional installation, 100% Compliant to California and Vermont low-lead requirements, For use in potable water distribution systems in accessible locations only 26613044873
CMP TO CMP STR NDL VAL 1/4 OD
Locke Part #: H0654MFG Part #: NV105-4X
Positive sealing & flow adjustment up to the capacity of the valve, Metal-to-metal seats with a fine thread engagement, Compliant needle valve options available for, California and Vermont low-lead requirements, Use with automotive & industrial applications for instrumentation, hydraulic and pneumatic systems., Not intended for use with natural gas, LPG (liquefied petroleum gas or propane), nuclear or avionic (aircraft) applications, 115 F maximum continuous use temperature 26613137490
CMP TO CMP STR NDL VAL 3/8 OD
Locke Part #: H0655MFG Part #: NV105-6X
Positive sealing & flow adjustment up to the capacity of the valve, Metal-to-metal seats with a fine thread engagement, Compliant needle valve options available for, California and Vermont low-lead requirements, Use with automotive & industrial applications for instrumentation, hydraulic and pneumatic systems., Not intended for use with natural gas, LPG (liquefied petroleum gas or propane), nuclear or avionic (aircraft) applications, 115 F maximum continuous use temperature 26613137483
Compression Cap 3/8" OD Tube
Locke Part #: H0579MFG Part #: 61CP-6 X
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Compression Cap 5/8" OD Tube
Locke Part #: H0580MFG Part #: 61CP-10
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Compression Nut 1/2" OD Tube
Locke Part #: H0572MFG Part #: 61-8
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Compression Nut 5/8" OD Tube
Locke Part #: H0573MFG Part #: 61-10
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems., Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
Little to no tube preparation. Compression fittings do not require flaring, soldering or other types of tube preparation, Available in a broad range of sizes, Compliant fitting options available for California and Vermont low-lead requirements, For use with instrumentation, hydraulic and pneumatic systems.Designed for use with aluminum, copper and plastic tubing. Not intended for use with steel tubing
One-piece construction, 100% Compliant product, For use in potable water distribution in accessible locations only.
Machined one-piece brass body provides strength, durability, and long-lasting performance, Oval knurled handle provides a secure grip and smooth on/off operation, No lead, For use in potable water distribution systems., Not intended for recirculating water systems that produce continuous use temperatures above 115 F.
Machined one-piece brass body provides strength, durability and long-lasting performance, Oval knurled handle provides a secure grip and smooth on/off operation, Compliant Multi-Turn Stops available for California, Vermont and Maryland low-lead Requirements, For use in potable water distribution systems., Not intended for recirculating water systems that produce continuous use temperatures above 115 F.
D/O VAL 1/2"IP ANG VAL 3/8"OD
Locke Part #: B0315MFG Part #: R1701LRX C1
Machined one-piece brass body provides strength, durability and long-lasting performance, Knurled oval handle provides a secure grip and smooth on/off operation, Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, Compliant Stops available for California and Vermont no-lead requirements., For use in potable water distribution systems., Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613137001
D/O VLV 1/2 NOM 3/8 OD COMP 1/4 OD COMP
Locke Part #: B0326MFG Part #: CR1900LX C1
Machined one-piece brass body provides strength, durability, and long-lasting performance., Knurled oval handle provides a secure grip and smooth on/off operation, Easy-to-remove handle helps protect against accidental stop operation during rough-ins, 100% Compliant, For use in potable water distribution systems, Not intended for recirculating water systems that produce continuous use temperatures above 115 F 26613138220
D/O VLV 1/2 NOM 3/8 OD COMP 1/4 OD COMP
Locke Part #: B0327MFG Part #: CR1900RX C1
Machined one-piece brass body provides strength, durability, and long-lasting performance., Knurled oval handle provides a secure grip and smooth on/off operation, Easy-to-remove handle helps protect against accidental stop operation during rough-ins, 100% Compliant, For use in potable water distribution systems, Not intended for recirculating water systems that produce continuous use temperatures above 115 F 26613136882
D/O VLV 1/2 NOM CMP X 3/8 CMP X 3/8 CMP
Locke Part #: B0248MFG Part #: CR1901DVSX R
Independent flow control. Dual outlet, dual shut-off operation permits you to shut-off water flow to one fixture while maintaining water flow to another fixture, Code approved replacement where separate shut-offs are required for two lines, Knurled oval handle provides a secure grip and smooth on/off operation, Straight inlet to outlet design (same-side outlets) is great for installations in tight spaces, Machined one-piece brass body provides strength, durability, and long-lasting performance, For use with water in accessible locations only., Easy-to-remove handle with screw attachment protects accidental stop operation during rough-ins, 100% compliant product available,, Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613137407
DIELECTRIC WASHER
Locke Part #: L0013MFG Part #: WRJ
26613051963
One-piece brass body provides strength, durability, and longer-lasting performance, Swivel hose thread nut simplifies fitting alignment to make the water connector installation quick and easy, High-temperature resistant washer for a reliable, longer-lasting performance, No Lead, To connect Whirlpool, Maytag, Amana, Kitchen Aid, and Jenn-Air dishwashers manufactured after September 2009 to flexible water connector., All female hose thread connections require a rubber washer inserted prior to installation.
026613004761
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines. Designed for use with aluminum, copper, brass and welded steel tubing that can be flared
FL F UN BR 5/8 OD TB X 1/2
Locke Part #: H0659MFG Part #: MAU1-10-8S
26613088570
FL M UN BR 5/8 OD TB X 1/2
Locke Part #: H0658MFG Part #: MAU2-10-8S
26613082684
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared.
Recommended for higher pressures than those covered by compression fittings, Resist mechanical pull out, Available in a broad range of sizes, For use with fuel, oil, liquefied petroleum (LP) and natural gas lines., Designed for use with aluminum, copper, brass and welded steel tubing that can be flared.
Flat Bibb Washer Assortment w/Screws
Locke Part #: M4000MFG Part #: SC2190
Includes: 39166039685
FULL PORT 3/4" GAS BALL VALVE
Locke Part #: M0464MFG Part #: TBV12F
Full flow operation. Full port design provides abundant water flow without obstruction, Blow-out proof stem is assembled from the inside with double o-rings to provide reliable performance, Heavy duty forged brass body, Right-sized handles ensures on-off operation even in tight installations, For use with natural, manufactured, mixed, liquefied-petroleum (LP) gas and LP gas-air mixtures. 26613139609
GAS CONN 3/4"FIPX3/4"MIP X24"
Locke Part #: L0669MFG Part #: CSSB21-24
Superior corrosion resistance to harsh chemicals found in common household cleaning, plumbing repair and masonry products., UV rays & salt resistant, ProCoat connectors are certified for indoor & outdoor use., Greater strength & flexibility with greater depth & number of corrugations to withstand greater torque & bend cycles, Outperforms industry standards for torsion (1.5X) without compromising the integrity of the coating or connector, Outperforms industry standard for repeated bending (2X) without compromising the integrity of the coating or connector, One-piece construction has no soldered of brazed joints, Smoother, burnished flare on connector ends seal with less torque, Uniform coat over entire length of connector for complete corrosion resistance of the stainless steel core, 100% leak tested, For use with indoor and outdoor connections of gas appliances to gas piping system, May be used with natural, manufactured, mixed and liquefied petroleum (LP or propane) gases and LP gas-air mixtures 26613118413
026613117812
LAV RIS 3/8 OD X 20 LG
Locke Part #: B0387MFG Part #: P1-20A
One-piece construction, Cut-to-Length for clean, professional installation, 100% Compliant to California and Vermont low-lead requirements, For use in potable water distribution systems in accessible locations only 26613044910
LAV RIS 3/8 OD X 30 LG
Locke Part #: B0388MFG Part #: P1-30A
One-piece construction, Cut-to-Length for clean, professional installation, 100% Compliant to California and Vermont low-lead requirements, For use in potable water distribution systems in accessible locations only 26613044958
Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, No Lead, PEX end designed to ASTM F1807, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems using ASTM F1807, and/or F2098 connection methods, Knurled oval handle provides a secure grip and smooth on/off operation,, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F.
Machined one-piece brass body provides strength, durability, and long-lasting performance., Knurled oval handle provides a secure grip and smooth on/off operation, Easy-to-remove handle helps protect against accidental stop operation during rough-ins, 100% Compliant, For use in potable water distribution systems, Not intended for recirculating water systems that produce continuous use temperatures above 115 F
Machined one-piece brass body provides strength, durability, and long-lasting performance, Knurled oval handle provides a secure grip and smooth on/off operation, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, No Lead, PEX end designed to ASTM F1807, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems using ASTM F1807, and/or F2098 connection methods, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F.
Independent flow control. Dual outlet, dual shut-off operation permits water flow to be controlled at one fixture while maintaining flow to the other fixture, Code approved replacement for areas requiring separate shut-offs for two lines, Machined one-piece brass body provides strength, durability and longer-lasting performance, Knurled oval handles provide a secure grip and smooth on/off operation, Easy-to-remove handle with screw attachment helps protect against accidental operation during the rough-in phase, Compliant Dual-Outlet, Dual-Shut-Off Stops available for California and Vermont low-lead requirements, Not intended for recirculating water systems that produce continuous use temperatures above 115 F., For use in potable water distribution systems.
Machined one-piece brass body provides strength, durability, and long-lasting performance, Knurled oval handle provides a secure grip and smooth on/off operation, No Lead, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems (parts containing PX and PXX only), For use in ASTM F877 water distribution systems as noted in Appendixes (parts containing PX and PXX only), For use in potable water distribution systems. Not intended for recirculating water systems that produce continuous use temperatures above 115 F.
NEV2-C1 CMP TO MIP ANG NDL
Locke Part #: H0643MFG Part #: NV104-4-2
Positive sealing & flow adjustment up to the capacity of the valve, Metal-to-metal seats with a fine thread engagement, For use with automotive & industrial applications for instrumentation, hydraulic and pneumatic systems., Not intended for use with natural gas, LPG (liquefied petroleum gas or propane), nuclear or avionic (aircraft) applications 26613078465
O-Ring Assortment
Locke Part #: M4012MFG Part #: SC0596
Made of high quality rubber, Comes in seven most popular sizes, Includes:, (2) SC0562, (2) SC0561, (2) SC0575, (2) SC0584, (2) SC0584, (2) SC0571, (1) SC0541, (1) SC0618. 39166039661
POLYMER BRD WTRHTCON3/4FIPX7/8ODCMPX18
Locke Part #: E0066MFG Part #: BWB20-18
Superior corrosion resistance to harsh chemicals found in common household cleaning and plumbing repair products,, Greater strength & flexibility. The patented polymer braid exhibits greater elasticity than stainless steel braiding, significantly increasing the flexibility of the connector, No kinking, no crimping. The polymer braided jacket is specially engineered to bend freely without kinking or crimping the connector, Won t work harden even with repeated bending, No dielectric union needed with installation as the braiding and rubber are constructed of non-conductive materials, Less torque to seal against the pliable rubber washer, especially on rough nipple surfaces, Longer connector nuts allow a greater number of thread-to-thread contacts and offer a better seal, Available for PEX connections, For use in exposed locations only to connect water heaters and other water connected devices to the water supply. 100% Compliant, Not intended for use with recirculating water systems that produce continuous use temperatures above 115 F. 26613965451
Self-Piercing Needle Valve Kits
Locke Part #: M0818MFG Part #: BC96X
Kit Includes:, Saddle Clamp w/Self-Locking Nuts, 1/4" OD x 25' Polyethylene Tube, Brass Sleeve & Inserts & Delrin Sleeve, 1/4" OD Union. 26613148977
SELFPIERCINGTAPVAL3/8TO1
Locke Part #: H0644MFG Part #: PNEV-NCV
Positive sealing & flow adjustment up to the capacity of the valve, Metal-to-metal seats with a fine thread engagement, Compliant needle valve options available for California and Vermont low-lead requirements, For use with automotive & industrial applications for instrumentation, hydraulic and pneumatic systems, Not intended for use with natural gas, LPG (liquefied petroleum gas or propane), nuclear or avionic (aircraft) applications, Kit Includes:, Needle valve, Saddle clamp, (2) Nuts, (2) Bolts, Washers, Brass compression sleeve for copper installations, Plastic sleeve/brass insert for plastic tube installations 26613078687
SERVICE VALVE KIT 3/4" IPS
Locke Part #: E1138MFG Part #: TWV30RX
Compact design ideal for recessed and cover box installations, Captive coupling nut & washer reduces opportunity for component loss making installation easier, Captive washer won t kink or tear during installation, Forged, one-piece construction reduces the potential for pinhole leaks, 100% Compliant, Integrated drain valve with independent, turn operation allows quick system diagnostic testing and maintenance, Built-in side port for the pressure relief valve reduces the number of connections & simplifies the installation, Right-sized handles, color-coded for immediate system identification. Perfect for tight installations, For use in potable water distribution systems for water flow control. Valves connect directly to cold water inlet and hot water outlet of the tankless water heater. Use for appliance maintenance and emergency shut-off. 26613141343
Product Image Not Available SERVICE VALVE KIT 3/4" SWT INL
Locke Part #: E1139MFG Part #: TWV3SRX
Compact design ideal for recessed and cover box installations, Captive coupling nut & washer reduces opportunity for component loss making installation easier, Captive washer won t kink or tear during installation, Forged, one-piece construction reduces the potential for pinhole leaks, 100% Compliant, Integrated drain valve with independent, turn operation allows quick system diagnostic testing and maintenance, Built-in side port for the pressure relief valve reduces the number of connections & simplifies the installation, Right-sized handles, color-coded for immediate system identification. Perfect for tight installations, For use in potable water distribution systems for water flow control. Valves connect directly to cold water inlet and hot water outlet of the tankless water heater. Use for appliance maintenance and emergency shut-off. 26613141404
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, 100% No Lead, For use in potable water distribution systems in accessible locations only
Engineered polymer braided fibers bend freely without kinking or crimping, 100% No Lead, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, TPE inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, For use in potable water distribution systems in accessible locations only.
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, Long wing nuts allow for quick connection and ensure dependable thread engagement, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only
Engineered polymer braided fibers bend freely without kinking or crimping, 100% No Lead, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, TPE inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, For use in potable water distribution systems in accessible locations only.
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only
Engineered polymer braided fibers bend freely without kinking or crimping, Reinforced PVC inner hose ensures durability, Rubber washers provide a large pliable sealing surface and ensure a long lasting water-tight connection, 8-sided pneumatic crimp provides greater dependability for realible nut-to-hose connections, 100% No Lead, For use in potable water distribution systems in accessible locations only
STAINLESS BRD 3/8X3/8CMP W/2
Locke Part #: M0649MFG Part #: S1-72DW612 F
Kit contains:, (1) 3/8 comp. x 3/8 comp. stainless steel dishwasher connector - 72" length, (1) 3/8 comp. x 3/4" hose fitting, (1) 3/8 comp. x 3/8 MIP fitting 26613159850
STR VAL 1/2 FIP X 3/8 CMP RIS
Locke Part #: B0236MFG Part #: OR12X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, Oval knurled handle provides a secure grip and smooth on/off operation, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, 100% Compliant product available, For use with water in accessible locations only., Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613138442
STR VLV 1/2 NOM CMP X 3/8 OD
Locke Part #: B0238MFG Part #: OCR14X C
Machined one-piece brass body provides strength, durability, and long-lasting performance, Knurled oval handle provides a secure grip and smooth on/off operation, No Lead, Easy-to-remove handle with screw attachment helps protect against accidental stop operation during rough-ins, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems (parts containing PX and PXX only), For use in ASTM F877 water distribution systems as noted in Appendixes (parts containing PX and PXX only), For use in potable water distribution systems. Not intended for recirculating water systems that produce continuous use temperatures above 115 F. 26613136981
STRAIGHT STOP W/CLD EXPANSION BARB
Locke Part #: R1283MFG Part #: G2CEPX14X C
One-piece shut-off mechanism provides smooth on-off operation without freeze ups even after long periods of non-use, Positive 1/4 turn shut off, Full-flow operation with no waterway obstructions, Corrosion-resistant handle is plated in an attractive chrome finish, Machined one-piece brass body provides strength, durability, and long-lasting performance, Easy-to-remove handle with screw attachment helps protect against accidental operation during rough-ins, 100% Leak tested, No Lead, PEX end designed to ASTM F1960, For use with ASTM F876 PEX tubing, in ASTM F877 water distribution systems, For use with water in accessible locations only., Not intended for recirculating systems that produce continuous use temperatures above 115 F. 26613141565
TEFLON VALVE PACKING 3/32 X 36 ROPE
Locke Part #: A4003MFG Part #: SF1335
39166039692