Loading ...

Loading ...

Search in: CAIN MFG. CO INC

L500.jpgGlastite Flexible Duct Connector
Locke Part #: L0500MFG Part #: CNRG100 Compare
Description Ext.: GLASSTITE FLEXIBLE DUCT 1-3/4" Metal, 3" Fabric, 1-3/4" Metal 28 Ga. Galvanized, "S LOC" SEAM
L501.jpg3/8" Dial Damper Blade Hardware
Locke Part #: L0501MFG Part #: DHDS38 Compare
Description Ext.: DAMPER REGULATOR 3/8" End Bearings, Dials & Quadrants. For dampers up to 20" Diameter. Zinc plated. 100 count.
L502.jpgKwik Regulator Set
Locke Part #: L0502MFG Part #: DHK-69 Compare
Description Ext.: KWIK REGULATOR SET CAIN Kwiki Regulator Sets - Hammer-On Type., K-69 Consists of:, 1 K708 Bearing, 1 K704 Washer, 1 K706 Wing Nut 12 Sets Poly bagged, 1 K705 Handle 144 Sets Ctn.
L503.jpg3/16 Urethane x 1/2" Wide x 50’
Locke Part #: L0503MFG Part #: DRUF3-12 Compare
Description Ext.: URETHANE GASKETING 1/2" Priced Per Roll
L510.jpg.475" For all 1/2", 2lb. Liner Box of 1000
Locke Part #: L0510MFG Part #: LF CMF050 Compare
Description Ext.: 1000 ct PINCHER IMPACT F The premium quality impact fastener Thru insulation impact fasteners.
L511.jpgMagnetic Hammer
Locke Part #: L0511MFG Part #: EQCPH-1 Compare
Description Ext.: MAGNETIC HAMMER For setting pinchers thru insulation., 2lb.
L514.jpg1-1/4" Duct Board Straight Clear Pins
Locke Part #: L0514MFG Part #: LFWP114 Compare
Description Ext.: 1 1/4" DUCT BD STR CLR
L514.jpg1-1/4" x 1-1/4" Duct Board Straight Clear Clips
Locke Part #: L0515MFG Part #: LFEOC-1 Compare
Description Ext.: 1 1/4" DUCT BD STR CLR
Material: Carbon alloy steel, Temperature Range: 32°F to 250°F The Pincher permanently fastens insulation to sheet metal in the fabrication of ductwork., Driving the tapered teeth into the softer metal causes the point to take a permanent set., Fasteners withstand a tensile pull of 80-120 pounds in sheet metal., To properly attach Pinchers to sheet metal, a hardened steel backer must be used as work surface at all times., A pre-attached cap holds the liner firmly in place and prevents insulation from pulling loose or delaminating., Pinchers can be used in conjunction with adhesives on any galvanized sheet metal with lockforming qualities of 26 gauge and higher, Technical Data:, Hardness: Point, shank and head are heat treated and tempered in a controlled atmosphere to a hardness of Rockwell C-50., Corrosion Resistance: Cain Pinchers are plated with .0002" to .0003" of zinc and receive a separate dip for corrosion resistance., Retaining Cap: Retaining cap is sufficient in size and design to depress the surface of the insulation without tearing or cutting it. The cap does not protrude into the air stream to create noise or interfere with air movement in the duct., Vibrations: Pinchers will not fatigue or be physically affected by vibrations normally found in high velocity air handling systems., Environmentally Safe: When used as intended, the Pinchers are non-toxic and considered safe as defined by current Federal Standards.
L510.jpg.63" dia for all 1", 12lb. Liner Box of 1000
Locke Part #: L0529MFG Part #: LF CMF 100 Compare
Description Ext.: PINCHER IMPACT FSTNR 1" The premium quality impact fastener Thru insulation impact fasteners.
L541.jpg1/2" Pin Size 1/2" 2 Lb. Liner Box of 5000
Locke Part #: L0541MFG Part #: LF-CWF-50B Compare
Description Ext.: POINTER WELD FSTNR Thru Insulation weld fastener. Sharp Rolled Point
L541.jpg1" Pin Size 1" H.D. 3 Lb. Liner Box of 5000
Locke Part #: L0542MFG Part #: LF-CWF-150B Compare
Description Ext.: POINTER WELD FASTNER 1" Thru Insulation weld fastener. Sharp Rolled Point
L541.jpg1" Pin Size 1" H.D. 3 Lb. Liner Box of 1000
Locke Part #: L0543MFG Part #: LF CWF 150 Compare
Description Ext.: POINTER WELD FSTNR 1" Thru Insulation weld fastener. Sharp Rolled Point
L1331.jpg3/4" Self Adhesive Hanger
Locke Part #: L1331MFG Part #: LF-SP-0750 Compare
Description Ext.: 3/4" SELF ADHESIVE
L1331.jpg1-1/4" Self AdhesiveHanger
Locke Part #: L1332MFG Part #: LF-SP-1250 Compare
Description Ext.: 1 1/4" SELF ADHESIVE