Loading ...

Search in: Commercial Category

Standard Features, Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Thermostatic Expansion Valves Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA, Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National Electrical Codes., All models are certified in accordance with the ULE certification program, which is based on AHRI Standard 340/360- 2007., All models are ASHRAE 90.1-2007 compliant., ISO 9001 Registered Manufacturing Quality System., Heating System, Optional Factory or Field Installed, Helix wound nichrome elements, Individual element limit controls, Wiring harness, Unit fuse block is furnished as standard, Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge., Copper tube Coil construction, enhanced rippled edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator Coil Cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity., Single formed Condenser coil., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections., Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Base rails have rigging holes., Three sides of the base rail have forklift slots., Raised edges around duct and power entry openings in the bottom of the unit provide additional protection against water entering the building., Units are shipped in downflow (vertical) configuration, can be field converted to horizontal airflow with optional Horizontal Discharge Kit., All panels adjacent to conditioned air are fully insulated with nonhygroscopic fiberglass insulation., Unit base is fully insulated. The insulation also serves as an air seal to the roof curb, eliminating the need to add a seal during installation. ALLIED AIR COMMERCIAL
L4398.jpg10 Ton 3PH 460V Electric Packaged Units
Locke Part #: L4401MFG Part #: V9151
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA, Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National Electrical Codes., All models are certified in accordance with the ULE certification program, which is based on AHRI Standard 340/360- 2007., All models are ASHRAE 90.1-2007 compliant., ISO 9001 Registered Manufacturing Quality System., Heating System, Optional Factory or Field Installed, Helix wound nichrome elements, Individual element limit controls, Wiring harness, Unit fuse block is furnished as standard, Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge., Copper tube Coil construction, enhanced rippled edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator Coil Cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity., Single formed Condenser coil., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections., Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Base rails have rigging holes., Three sides of the base rail have forklift slots., Raised edges around duct and power entry openings in the bottom of the unit provide additional protection against water entering the building., Units are shipped in downflow (vertical) configuration, can be field converted to horizontal airflow with optional Horizontal Discharge Kit., All panels adjacent to conditioned air are fully insulated with nonhygroscopic fiberglass insulation., Unit base is fully insulated. The insulation also serves as an air seal to the roof curb, eliminating the need to add a seal during installation. ALLIED AIR COMMERCIAL
Standard Features, Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Thermostatic Expansion Valves Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Standard Features, Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Thermostatic Expansion Valves Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge. ALLIED AIR COMMERCIAL
Standard Features, Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Thermostatic Expansion Valves Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not Available14W33 15KW 1PH HT STRIP
Locke Part #: L4364MFG Part #: 14W33
ALLIED AIR COMMERCIAL
Product Image Not Available15 kW Heat Strip for KHA, KCA
Locke Part #: L4310MFG Part #: 14W36
ALLIED AIR COMMERCIAL
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA, Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National Electrical Codes., All models are certified in accordance with the ULE certification program, which is based on AHRI Standard 340/360- 2007, All models are ASHRAE 90.1-2007 compliant., ISO 9001 Registered Manufacturing Quality System., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Copper tube Coil construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections, Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount, Outdoor Coil Fans PVC coated fan guard furnished. ALLIED AIR COMMERCIAL
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA, Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National Electrical Codes., All models are certified in accordance with the ULE certification program, which is based on AHRI Standard 340/360- 2007, All models are ASHRAE 90.1-2007 compliant., ISO 9001 Registered Manufacturing Quality System., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Copper tube Coil construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections, Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount, Outdoor Coil Fans PVC coated fan guard furnished. ALLIED AIR COMMERCIAL
RSI's 510 SERIES concentric diffuser systems are designed to provide a single point air distribution system. The systems may be used with either a T-Bar ceiling or a plaster ceiling., Standard features include:, 1., All Aluminum diffuser with aluminum return air egg crate., 2., Built-in Anti-Sweat gasket., 3., Molded Fiberglass Transition (through five tons)., 4., Built-in hanging supports., 5., Diffuser box constructed of fiberglass duct board (through 7.5 tons) or sheet metal., Standard benefits include:, 1., Even four way airflow., 2., Factory assembled & sealed., 3., Guaranteed not to "sweat"., 4., Guaranteed not to recirculate air flow (short cycle)., 5., Return air egg crate is easily removed., 6., Units are fully insulated (both supply and return). RRS ROOFTOP SYSTEMS
Product Image Not Available18" Height Downflow Hybrid Roof Curbs
Locke Part #: L9646MFG Part #: 10Z26
ALLIED AIR COMMERCIAL
RSI's 510 SERIES concentric diffuser systems are designed to provide a single point air distribution system. The systems may be used with either a T-Bar ceiling or a plaster ceiling., Standard features include:, 1., All Aluminum diffuser with aluminum return air egg crate., 2., Built-in Anti-Sweat gasket., 3., Molded Fiberglass Transition (through five tons)., 4., Built-in hanging supports., 5., Diffuser box constructed of fiberglass duct board (through 7.5 tons) or sheet metal., Standard benefits include:, 1., Even four way airflow., 2., Factory assembled & sealed., 3., Guaranteed not to "sweat"., 4., Guaranteed not to recirculate air flow (short cycle)., 5., Return air egg crate is easily removed., 6., Units are fully insulated (both supply and return). RRS ROOFTOP SYSTEMS
RSI's 510 SERIES concentric diffuser systems are designed to provide a single point air distribution system. The systems may be used with either a T-Bar ceiling or a plaster ceiling., Standard features include:, 1., All Aluminum diffuser with aluminum return air egg crate., 2., Built-in Anti-Sweat gasket., 3., Molded Fiberglass Transition (through five tons)., 4., Built-in hanging supports., 5., Diffuser box constructed of fiberglass duct board (through 7.5 tons) or sheet metal., Standard benefits include:, 1., Even four way airflow., 2., Factory assembled & sealed., 3., Guaranteed not to "sweat"., 4., Guaranteed not to recirculate air flow (short cycle)., 5., Return air egg crate is easily removed., 6., Units are fully insulated (both supply and return). RRS ROOFTOP SYSTEMS
Product Image Not Available22.5 kW Heat Strip for KHA, KCA
Locke Part #: L4311MFG Part #: 14W37
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Approvals, AHRI Certified to AHRI Standard 210/240-2008. CSA listed, Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410a Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., High Pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil, Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components. ALLIED AIR COMMERCIAL
ALLIED AIR ENTERPRISES INC
L9609.jpg3 Ton 460V / 3PH Electric Package Units
Locke Part #: L9610MFG Part #: V9627
Approvals, AHRI Certified to AHRI Standard 210/240-2008. CSA listed, Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410a Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., High Pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil, Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components. ALLIED AIR ENTERPRISES INC
ALLIED AIR ENTERPRISES INC
L9615.jpg3 Ton 460V / 3PH Heat Pump Packaged Units
Locke Part #: L9616MFG Part #: V9670
COOLING / HEATING SYSTEM, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410A Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., Compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., Compressor Crankcase Heater, Protects against refrigerant migration that can occur during low ambient operation., High pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Reversing Valve, 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover from cooling to heating and vice versa., Defrost Control, Provides a defrost cycle, if needed, every 30 or 60 or 90 minutes (adjustable) of compressor on time at outdoor coil temperature below 35 F. Temperature switch mounted on outdoor coil liquid line terminates defrost cycle., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Coil Construction, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Indoor Coil, Cross row circuiting with rifled tubing optimizes both sensible and latent cooling capacity., Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., CABINET, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., WARRANTY, Limited five years on compressors., Limited one year all other covered components., APPROVALS, AHRI Certified to AHRI Standard 210/240-2008., CSA listed., Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System. ALLIED AIR ENTERPRISES INC
Approvals, AHRI Certified to AHRI Standard 210/240-2008. CSA listed, Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410a Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., High Pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil, Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
COOLING / HEATING SYSTEM, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410A Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., Compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., Compressor Crankcase Heater, Protects against refrigerant migration that can occur during low ambient operation., High pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Reversing Valve, 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover from cooling to heating and vice versa., Defrost Control, Provides a defrost cycle, if needed, every 30 or 60 or 90 minutes (adjustable) of compressor on time at outdoor coil temperature below 35 F. Temperature switch mounted on outdoor coil liquid line terminates defrost cycle., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Coil Construction, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Indoor Coil, Cross row circuiting with rifled tubing optimizes both sensible and latent cooling capacity., Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., CABINET, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., WARRANTY, Limited five years on compressors., Limited one year all other covered components., APPROVALS, AHRI Certified to AHRI Standard 210/240-2008., CSA listed., Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System. ALLIED AIR ENTERPRISES INC
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA., Components bonded for grounding to meet safety standards for servicing required by UL., Certified in accordance with the USE certification program, which is based on ARI Standard 210/240-2006, All models are ASHRAE 90.1 compliant., All models are ENERGY STAR certified, ISO 9001 Registered manufacturing quality system., Cabinet, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Electrical and gas lines can be brought through the unit base or through horizontal access knock-outs. Optional bottom gas entry kit is available., Access panels are provided for the economizer/filter section, heating/blower section, and the compressor/controls section., Cooling system, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 f to 125 f without any additional controls., Compressor resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., Thermal expansion valve assures optimal performance throughout the application range. Removable element head., High pressure switch protects the compressor from overload conditions such as dirty condenser coils, blockedrefrigerant flow, or loss of outdoor fan operation., High capacity filter/drier protects from dirt and moisture, Freezestat protects the evaporator coil from damaging ice build-up due to conditions such as low/no air flow, or low refrigerant charge., Copper tube coil construction, enhanced rippled-edgealuminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator coil with cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity, Two independent formed condenser coils allow separation for cleaning., Plastic condensate drain pan, sloped to meet drainage requirements of ASHRAE 62.1. Side or bottom drain connections. Reversible to allow connection at back of unit., PVC coated fan guard furnished. ALLIED AIR COMMERCIAL
L9609.jpg4 Ton 460V / 3PH Electric Package Units
Locke Part #: L9612MFG Part #: V9630
Approvals, AHRI Certified to AHRI Standard 210/240-2008. CSA listed, Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410a Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., High Pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil, Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components. ALLIED AIR ENTERPRISES INC
ALLIED AIR COMMERCIAL
L9615.jpg4 Ton 460V / 3PH Heat Pump Packaged Units
Locke Part #: L9618MFG Part #: V9672
COOLING / HEATING SYSTEM, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410A Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., Compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., Compressor Crankcase Heater, Protects against refrigerant migration that can occur during low ambient operation., High pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Reversing Valve, 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover from cooling to heating and vice versa., Defrost Control, Provides a defrost cycle, if needed, every 30 or 60 or 90 minutes (adjustable) of compressor on time at outdoor coil temperature below 35 F. Temperature switch mounted on outdoor coil liquid line terminates defrost cycle., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Coil Construction, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Indoor Coil, Cross row circuiting with rifled tubing optimizes both sensible and latent cooling capacity., Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., CABINET, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., WARRANTY, Limited five years on compressors., Limited one year all other covered components., APPROVALS, AHRI Certified to AHRI Standard 210/240-2008., CSA listed., Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System. ALLIED AIR COMMERCIAL
COOLING / HEATING SYSTEM, Designed to maximize sensible and latent cooling performance at design conditions. System can operate from 30 F to 125 F without any additional controls., Refrigerant, Non-chlorine, ozone friendly R-410A. Unit pre-charged with refrigerant., Compressor, Scroll compressors resiliently mounted on rubber grommets for high performance, reliability and quiet operation., Compressor Crankcase Heater, Protects against refrigerant migration that can occur during low ambient operation., High Pressure Switch Check/Thermal Expansion Valves Reversing Valves, 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover., Defrost Control, Provides a defrost cycle, if needed, every 30 or 60 or 90 minutes (adjustable)., Filter/Drier Freezestat, Protects the evaporator coil from damaging ice build-up., Coil Construction, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested. Indoor Coil Cross row circuiting with rifled copper tubing., Outdoor Coil, Two independent formed coils allow separation for cleaning., Condensate Drain Pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1. Side or bottom drain connections. Reversible., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, shaft up, wire basket mount. Outdoor Coil Fan PVC coated fan guard furnished., CABINET, Construction, Heavy-gauge galvanized steel panels with a two-layer enamel paint finish and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Air-Flow Choice, Units are shipped in down-flow (vertical) configuration, can be field converted to horizontal air flow configuration without a kit., Power Entry, Through the base or horizontal knock- outs., Insulation, All panels adjacent to conditioned air are fully insulated with non-hygroscopic fiberglass insulation. Base is fully insulated., CONTROLS, Unit Control, All control voltage is provided via a 24V (secondary) transformer with built-in circuit breaker protection., Heat/Cool Staging, - Capable of up to 2 heat / 2 cool staging with a third party DDC control system or thermostat., Low Voltage Terminal Block, - Provides screw terminal connections for thermostat or controller wiring. Night Setback Mode - Saves energy by closing outdoor air dampers and operating supply fan on thermostat demand only., BLOWER, A wide selection of supply air blower options are available to meet a variety of air flow requirements., Motor, Supply Air Blower, Forward curved blades, blower wheel is statically and dynamically balanced. All belt drive motors have adjustable pulley for speed change., Indoor Air Quality -, Disposable 2 inch air filters furnished., Net Cooling Capacity 47,000 to 59,000 Btuh, Net Heating Capacity 48,000 to 60,500 Btuh, Optional Electric Heat 7.5 to 30 kW ALLIED AIR COMMERCIAL
APPLICATIONS, Convertible upflow or horizontal design., Each refrigerant circuit has a dedicated expansion valve., Dual distribution system for two stage capacity control during cooling cycles., Air handlers are shipped factory assembled ready to install. Standard static blower drive is furnished factory installed., REFRIGERANT SYSTEM, Multi-Circuit, Copper Tube Coil, Coils on 090-120 models are face split with separate circuits, each circuit has its own expansion valve., Coil is constructed of aluminum fins fitted to durable seamless, rifled copper tubes., Flared tubing connections and silver soldering provide tight, leakproof joints., Refrigerant Piping and Drain Connections, Refrigerant line inlets (knockouts) are provided on both sides of the cabinet., Refrigerant lines require sweat connections and are made internal to the cabinet., Condensate drain outlet extends outside the cabinet for ease of connection. Condensate drain can be relocated and repositioned., BELT DRIVE BLOWERS, Single blower wheel., Centrifugal belt driven blowers deliver large air volumes quietly and with low power consumption., Heavy-duty blower wheels, with forward curved blades and double inlet are statically and dynamically balanced., Heavy-duty bearings are permanently sealed and lubricated., CABINET, Cabinet is constructed of heavy-gauge, galvanized steel completely lined with thick fiberglass insulation for quiet and efficient operation., Drain Pan, Deep, corrosion resistant plastic drain pan. ALLIED AIR COMMERCIAL
L4336.jpg45W69 TAA120S4DG 10TAH 460V R410A
Locke Part #: L4340MFG Part #: 45W69
APPLICATIONS, Convertible upflow or horizontal design., Each refrigerant circuit has a dedicated expansion valve., Dual distribution system for two stage capacity control during cooling cycles., Air handlers are shipped factory assembled ready to install. Standard static blower drive is furnished factory installed., REFRIGERANT SYSTEM, Multi-Circuit, Copper Tube Coil, Coils on 090-120 models are face split with separate circuits, each circuit has its own expansion valve., Coil is constructed of aluminum fins fitted to durable seamless, rifled copper tubes., Flared tubing connections and silver soldering provide tight, leakproof joints., Refrigerant Piping and Drain Connections, Refrigerant line inlets (knockouts) are provided on both sides of the cabinet., Refrigerant lines require sweat connections and are made internal to the cabinet., Condensate drain outlet extends outside the cabinet for ease of connection. Condensate drain can be relocated and repositioned., BELT DRIVE BLOWERS, Single blower wheel., Centrifugal belt driven blowers deliver large air volumes quietly and with low power consumption., Heavy-duty blower wheels, with forward curved blades and double inlet are statically and dynamically balanced., Heavy-duty bearings are permanently sealed and lubricated., CABINET, Cabinet is constructed of heavy-gauge, galvanized steel completely lined with thick fiberglass insulation for quiet and efficient operation., Drain Pan, Deep, corrosion resistant plastic drain pan. ALLIED AIR COMMERCIAL
Product Image Not Available46W51 15KW HT STRP 208/230V
Locke Part #: L4341MFG Part #: 46W51
ALLIED AIR COMMERCIAL
4SCU13LC.jpg4SCU13LC136F 3 TON R410A 460V 3PH 13SEER COND
Locke Part #: L6788MFG Part #: 1.334040
Compressor, High-efficiency scroll compressor, R410A refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Filter drier installed for system protection, Service valves positioned for quick installation and easy service, Indoor coil orifice shipped with outdoor unit for optimum efficiency and capacity, Charged for 15ft. of line set Trade available components, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, R410a Refrigerant, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
Compressor, High-efficiency scroll compressor, R410A refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Filter drier installed for system protection, Service valves positioned for quick installation and easy service, Indoor coil orifice shipped with outdoor unit for optimum efficiency and capacity, Charged for 15ft. of line set Trade available components, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, R410a Refrigerant, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
4SCU13LC.jpg4SCU13LC148F 4 TON R410A 460V 3PH 13SEER COND
Locke Part #: L6789MFG Part #: 1.334041
Compressor, High-efficiency scroll compressor, R410A refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Filter drier installed for system protection, Service valves positioned for quick installation and easy service, Indoor coil orifice shipped with outdoor unit for optimum efficiency and capacity, Charged for 15ft. of line set Trade available components, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, R410a Refrigerant, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
Compressor, High-efficiency scroll compressor, R410A refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Filter drier installed for system protection, Service valves positioned for quick installation and easy service, Indoor coil orifice shipped with outdoor unit for optimum efficiency and capacity, Charged for 15ft. of line set Trade available components, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, R410a Refrigerant, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
Compressor, High-efficiency scroll compressor, R410A refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Filter drier installed for system protection, Service valves positioned for quick installation and easy service, Indoor coil orifice shipped with outdoor unit for optimum efficiency and capacity, Charged for 15ft. of line set Trade available components, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, R410a Refrigerant, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
Compressor, High-efficiency scroll compressor, R410A refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Filter drier installed for system protection, Service valves positioned for quick installation and easy service, Indoor coil orifice shipped with outdoor unit for optimum efficiency and capacity, Charged for 15ft. of line set Trade available components, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, R410a Refrigerant, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
L6732.jpg4SHP13LC148F 4T 3PH 460V R410A CONDENSER
Locke Part #: L6732MFG Part #: 1.434027
Compressor, High-efficiency scroll compressor, R410a refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Raised base pan with ports allows for excellent water and debris drainage, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Bi-directional filter drier for long-lasting durability and system protection, Discharge muffler for quiet operation, Reliable, solid-state, time-initiated, temperature-terminated defrost system, Service valves positioned for quick installation and easy service, Low pressure switch for loss of charge system protection, Trade-available components, Defrost control features built-in diagnostics for easier service, Defrost control has short cycle protection to protect compressor, Defrost control is Quiet Shift capable, Defrost cycle is field selectable 30/60/90 minutes, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
Compressor, High-efficiency scroll compressor, R410a refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Raised base pan with ports allows for excellent water and debris drainage, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Bi-directional filter drier for long-lasting durability and system protection, Discharge muffler for quiet operation, Reliable, solid-state, time-initiated, temperature-terminated defrost system, Service valves positioned for quick installation and easy service, Low pressure switch for loss of charge system protection, Trade-available components, Defrost control features built-in diagnostics for easier service, Defrost control has short cycle protection to protect compressor, Defrost control is Quiet Shift capable, Defrost cycle is field selectable 30/60/90 minutes, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
L6732.jpg4SHP13LC160F 5T 3PH 460V R410A CONDENSER
Locke Part #: L6733MFG Part #: 1.434028
Compressor, High-efficiency scroll compressor, R410a refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Raised base pan with ports allows for excellent water and debris drainage, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Bi-directional filter drier for long-lasting durability and system protection, Discharge muffler for quiet operation, Reliable, solid-state, time-initiated, temperature-terminated defrost system, Service valves positioned for quick installation and easy service, Low pressure switch for loss of charge system protection, Trade-available components, Defrost control features built-in diagnostics for easier service, Defrost control has short cycle protection to protect compressor, Defrost control is Quiet Shift capable, Defrost cycle is field selectable 30/60/90 minutes, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
Compressor, High-efficiency scroll compressor, R410a refrigerant, Grommet-mounted compressor for quiet operation, Internally protected against high temperature motor overload conditions, Cabinet, Full metal louvered panel coil guard protection, Controls located in corner post for easy installation and service, Rounded corners for safety and attractive, clean appearance, Baked polyester paint finish over galvanized steel for maximum durability, External gauge ports for easy service, Raised base pan with ports allows for excellent water and debris drainage, Coil, Enhanced aluminum fins and copper tubing for high efficiency and capacity, Raised coil prevents debris from collecting in bottom of coil and causing loss of airflow, Components, Full metal louvered panels remove with just two screws per panel for easy coil cleaning and service, Bi-directional filter drier for long-lasting durability and system protection, Discharge muffler for quiet operation, Reliable, solid-state, time-initiated, temperature-terminated defrost system, Service valves positioned for quick installation and easy service, Low pressure switch for loss of charge system protection, Trade-available components, Defrost control features built-in diagnostics for easier service, Defrost control has short cycle protection to protect compressor, Defrost control is Quiet Shift capable, Defrost cycle is field selectable 30/60/90 minutes, 5 Year Limited Warranty on compressor, 1 Year Limited Warranty on all parts ARMSTRONG AIR
COOLING / HEATING SYSTEM, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410A Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., Compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., Compressor Crankcase Heater, Protects against refrigerant migration that can occur during low ambient operation., High pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Reversing Valve, 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover from cooling to heating and vice versa., Defrost Control, Provides a defrost cycle, if needed, every 30 or 60 or 90 minutes (adjustable) of compressor on time at outdoor coil temperature below 35 F. Temperature switch mounted on outdoor coil liquid line terminates defrost cycle., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Coil Construction, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Indoor Coil, Cross row circuiting with rifled tubing optimizes both sensible and latent cooling capacity., Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., CABINET, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., WARRANTY, Limited five years on compressors., Limited one year all other covered components., APPROVALS, AHRI Certified to AHRI Standard 210/240-2008., CSA listed., Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System. ALLIED AIR COMMERCIAL
L9609.jpg5 Ton 460V / 3PH Electric Package Units
Locke Part #: L9614MFG Part #: V9633
Approvals, AHRI Certified to AHRI Standard 210/240-2008. CSA listed, Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410a Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., High Pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil, Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components. ALLIED AIR ENTERPRISES INC
L9615.jpg5 Ton 460V / 3PH Heat Pump Packaged Units
Locke Part #: L9620MFG Part #: V9674
COOLING / HEATING SYSTEM, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 35 F to 125 F without any additional controls., R-410A Refrigerant, Non-chlorine, ozone friendly, R-410A., Unit is factory pre-charged with refrigerant. See Specifications Table., Compressor, Resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., Compressor Crankcase Heater, Protects against refrigerant migration that can occur during low ambient operation., High pressure Switch, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Reversing Valve, 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover from cooling to heating and vice versa., Defrost Control, Provides a defrost cycle, if needed, every 30 or 60 or 90 minutes (adjustable) of compressor on time at outdoor coil temperature below 35 F. Temperature switch mounted on outdoor coil liquid line terminates defrost cycle., Filter/Drier, High capacity filter/drier protects the system from dirt and moisture., Coil Construction, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Indoor Coil, Cross row circuiting with rifled tubing optimizes both sensible and latent cooling capacity., Condensate Drain pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1., End drain connection., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, permanently lubricated bearings, shaft down, fan guard mount., Outdoor Coil Fan Guard, PVC coated fan guard furnished., CABINET, Heavy-gauge steel panels and full perimeter heavy gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., WARRANTY, Limited five years on compressors., Limited one year all other covered components., APPROVALS, AHRI Certified to AHRI Standard 210/240-2008., CSA listed., Units are Certified by CSA., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes., All models are ASHRAE 90.1 compliant., ISO 9001 Registered Manufacturing Quality System. ALLIED AIR COMMERCIAL
COOLING / HEATING SYSTEM, Designed to maximize sensible and latent cooling performance at design conditions. System can operate from 30 F to 125 F without any additional controls., Refrigerant, Non-chlorine, ozone friendly R-410A. Unit pre-charged with refrigerant., Compressor, Scroll compressors resiliently mounted on rubber grommets for high performance, reliability and quiet operation., Compressor Crankcase Heater, Protects against refrigerant migration that can occur during low ambient operation., High Pressure Switch Check/Thermal Expansion Valves Reversing Valves, 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover., Defrost Control, Provides a defrost cycle, if needed, every 30 or 60 or 90 minutes (adjustable)., Filter/Drier Freezestat, Protects the evaporator coil from damaging ice build-up., Coil Construction, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested. Indoor Coil Cross row circuiting with rifled copper tubing., Outdoor Coil, Two independent formed coils allow separation for cleaning., Condensate Drain Pan, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1. Side or bottom drain connections. Reversible., Outdoor Coil Fan Motor, Thermal overload protected, totally enclosed, shaft up, wire basket mount. Outdoor Coil Fan PVC coated fan guard furnished., CABINET, Construction, Heavy-gauge galvanized steel panels with a two-layer enamel paint finish and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Air-Flow Choice, Units are shipped in down-flow (vertical) configuration, can be field converted to horizontal air flow configuration without a kit., Power Entry, Through the base or horizontal knock- outs., Insulation, All panels adjacent to conditioned air are fully insulated with non-hygroscopic fiberglass insulation. Base is fully insulated., CONTROLS, Unit Control, All control voltage is provided via a 24V (secondary) transformer with built-in circuit breaker protection., Heat/Cool Staging, - Capable of up to 2 heat / 2 cool staging with a third party DDC control system or thermostat., Low Voltage Terminal Block, - Provides screw terminal connections for thermostat or controller wiring. Night Setback Mode - Saves energy by closing outdoor air dampers and operating supply fan on thermostat demand only., BLOWER, A wide selection of supply air blower options are available to meet a variety of air flow requirements., Motor, Supply Air Blower, Forward curved blades, blower wheel is statically and dynamically balanced. All belt drive motors have adjustable pulley for speed change., Indoor Air Quality -, Disposable 2 inch air filters furnished., Net Cooling Capacity 47,000 to 59,000 Btuh, Net Heating Capacity 48,000 to 60,500 Btuh, Optional Electric Heat 7.5 to 30 kW ALLIED AIR COMMERCIAL
Product Image Not Available53W94 30KW 460V 3PH STRIP HEAT
Locke Part #: L4373MFG Part #: 53W94
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Standard Features, R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel, Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Reversible Drain Pan Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves - Provide peak cooling performance across the entire application range., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge., Copper tube Coil construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator Coil Cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity, Single formed Condenser coil., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections, Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount, Outdoor Coil Fans PVC coated fan guard furnished. ALLIED AIR COMMERCIAL
Standard Features, R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel, Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Reversible Drain Pan Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves - Provide peak cooling performance across the entire application range., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge., Copper tube Coil construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator Coil Cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity, Single formed Condenser coil., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections, Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount, Outdoor Coil Fans PVC coated fan guard furnished. ALLIED AIR COMMERCIAL
Standard Features, Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Thermostatic Expansion Valves Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA, Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National Electrical Codes., All models are certified in accordance with the ULE certification program, which is based on AHRI Standard 340/360- 2007., All models are ASHRAE 90.1-2007 compliant., ISO 9001 Registered Manufacturing Quality System., Heating System, Optional Factory or Field Installed, Helix wound nichrome elements, Individual element limit controls, Wiring harness, Unit fuse block is furnished as standard, Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge., Copper tube Coil construction, enhanced rippled edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator Coil Cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity., Single formed Condenser coil., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections., Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Base rails have rigging holes., Three sides of the base rail have forklift slots., Raised edges around duct and power entry openings in the bottom of the unit provide additional protection against water entering the building., Units are shipped in downflow (vertical) configuration, can be field converted to horizontal airflow with optional Horizontal Discharge Kit., All panels adjacent to conditioned air are fully insulated with nonhygroscopic fiberglass insulation., Unit base is fully insulated. The insulation also serves as an air seal to the roof curb, eliminating the need to add a seal during installation. ALLIED AIR COMMERCIAL
L4398.jpg7.5 Ton 3PH 460V Electric Packaged Units
Locke Part #: L4399MFG Part #: V9145
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA, Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National Electrical Codes., All models are certified in accordance with the ULE certification program, which is based on AHRI Standard 340/360- 2007., All models are ASHRAE 90.1-2007 compliant., ISO 9001 Registered Manufacturing Quality System., Heating System, Optional Factory or Field Installed, Helix wound nichrome elements, Individual element limit controls, Wiring harness, Unit fuse block is furnished as standard, Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge., Copper tube Coil construction, enhanced rippled edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator Coil Cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity., Single formed Condenser coil., Plastic Condensate Drain Pan, sloped to meet drainage requirements of ASHRAE 62.1., Side or bottom drain connections., Reversible to allow connection at back of unit., Outdoor Coil Fan Motors Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans PVC coated fan guard furnished., Cabinet, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Base rails have rigging holes., Three sides of the base rail have forklift slots., Raised edges around duct and power entry openings in the bottom of the unit provide additional protection against water entering the building., Units are shipped in downflow (vertical) configuration, can be field converted to horizontal airflow with optional Horizontal Discharge Kit., All panels adjacent to conditioned air are fully insulated with nonhygroscopic fiberglass insulation., Unit base is fully insulated. The insulation also serves as an air seal to the roof curb, eliminating the need to add a seal during installation. ALLIED AIR COMMERCIAL
Standard Features, Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly, High Pressure Switches - Protect compressor., Scroll Compressors - Single speed scroll compressors are furnished on all models., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Thermostatic Expansion Valves Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits., Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shutoff., Heat Exchanger Tubular construction, aluminized steel, life cycle tested. Optional Stainless Steel Heat Exchanger is required if mixed air temperature is below 45 F., Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Ignition control is factory installed in the controls section., Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant is Non-chlorine based, ozone friendly., Scroll compressors on all models for high performance, reliability and quiet operation., Resiliently mounted on rubber grommets for quiet operation., Thermal Expansion Valves Assures optimal performance throughout the application range., High Pressure Switch Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Freezestats Protect the evaporator coil from damaging ice build-up due to conditions such as low/no airflow, or low refrigerant charge. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
L4415.jpgACBX32CM-136-230-6 3 TON 3PH AIR HANDLER
Locke Part #: L4415MFG Part #: 52W62
Application, Environmentally friendly R410A refrigerant, 3, 4, and 5 ton nominal capacities, Multi-position applications, One piece design for easy installation but may be disassembled into two separate sections for ease of installation in tight applications, Optional field installed electric heat kits, 10, 15 and 20kW, Heat pump and air conditioner applications, Cabinet, Foil faced insulation, Painted, heavy-gauge galvanized cabinet, Tool-less access to filter area for quick and easy servicing. Disposable frame type filter furnished and factory installed in rails in cabinet, High-strength, UV and heat-resistant plastic drain pan for corrosion resistance have dual pipe drains, Serviceable easy slide out blower assembly, No external screw heads on sides of cabinet for tight installations preventing damage to walls or woodwork, Removable panels provide complete service access, Electrical inlets provided in sides and top of cabinet, Components, Efficient multi-speed PSC blower motors, Standard transformer and blower relay, Built-in indoor time delay for increases efficiency, Sleeves on distributor tubing to protect tubing, Drain pan designed for up-flow, down-flow or horizontal applications. Deep, corrosion resistant plastic drain pans have dual pipe drains, Factory installed R410A TXV, Accessories, Counterflow kit, Combustible floor kit, Single point power kit, Electric heat kits Warranty, 1 year parts warranty. See limited warranty document for details ARMSTRONG AIR
L4415.jpgACBX32CM-148-230-6 4 TON 3PH AIR HANDLER
Locke Part #: L4416MFG Part #: 52W63
Application, Environmentally friendly R410A refrigerant, 3, 4, and 5 ton nominal capacities, Multi-position applications, One piece design for easy installation but may be disassembled into two separate sections for ease of installation in tight applications, Optional field installed electric heat kits, 10, 15 and 20kW, Heat pump and air conditioner applications, Cabinet, Foil faced insulation, Painted, heavy-gauge galvanized cabinet, Tool-less access to filter area for quick and easy servicing. Disposable frame type filter furnished and factory installed in rails in cabinet, High-strength, UV and heat-resistant plastic drain pan for corrosion resistance have dual pipe drains, Serviceable easy slide out blower assembly, No external screw heads on sides of cabinet for tight installations preventing damage to walls or woodwork, Removable panels provide complete service access, Electrical inlets provided in sides and top of cabinet, Components, Efficient multi-speed PSC blower motors, Standard transformer and blower relay, Built-in indoor time delay for increases efficiency, Sleeves on distributor tubing to protect tubing, Drain pan designed for up-flow, down-flow or horizontal applications. Deep, corrosion resistant plastic drain pans have dual pipe drains, Factory installed R410A TXV, Accessories, Counterflow kit, Combustible floor kit, Single point power kit, Electric heat kits Warranty, 1 year parts warranty. See limited warranty document for details ARMSTRONG AIR
L4415.jpgACBX32CM-160-230-6 5 TON 3PH AIR HANDLER
Locke Part #: L4417MFG Part #: 52W64
Application, Environmentally friendly R410A refrigerant, 3, 4, and 5 ton nominal capacities, Multi-position applications, One piece design for easy installation but may be disassembled into two separate sections for ease of installation in tight applications, Optional field installed electric heat kits, 10, 15 and 20kW, Heat pump and air conditioner applications, Cabinet, Foil faced insulation, Painted, heavy-gauge galvanized cabinet, Tool-less access to filter area for quick and easy servicing. Disposable frame type filter furnished and factory installed in rails in cabinet, High-strength, UV and heat-resistant plastic drain pan for corrosion resistance have dual pipe drains, Serviceable easy slide out blower assembly, No external screw heads on sides of cabinet for tight installations preventing damage to walls or woodwork, Removable panels provide complete service access, Electrical inlets provided in sides and top of cabinet, Components, Efficient multi-speed PSC blower motors, Standard transformer and blower relay, Built-in indoor time delay for increases efficiency, Sleeves on distributor tubing to protect tubing, Drain pan designed for up-flow, down-flow or horizontal applications. Deep, corrosion resistant plastic drain pans have dual pipe drains, Factory installed R410A TXV, Accessories, Counterflow kit, Combustible floor kit, Single point power kit, Electric heat kits Warranty, 1 year parts warranty. See limited warranty document for details ARMSTRONG AIR
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableCoil/Hail Guards for 7.5-12.5T Z-Series
Locke Part #: L9650MFG Part #: 12X21
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableECB29-15CB-4Y 15 KW HEAT STRIP 3PH
Locke Part #: L4464MFG Part #: 12L63
ARMSTRONG AIR
Product Image Not AvailableECB29-20CBY 20 KW HEAT STRIP 3PH
Locke Part #: L4465MFG Part #: 12L64
ARMSTRONG AIR
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableEconomizer for 3, 4, 5 ton TGA, KHA, KCA
Locke Part #: L4105MFG Part #: 14D90
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableFor 024-090 (2 - 7-1/2 Ton) KG, KC, KH
Locke Part #: L4360MFG Part #: 53W78
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableFor 10 Ton KG-KC-KH Package Units
Locke Part #: L4117MFG Part #: 12X66
ALLIED AIR COMMERCIAL
Product Image Not AvailableFor 2-6 Ton KG-KC-KH Package Units
Locke Part #: L4344MFG Part #: 41W33
ALLIED AIR COMMERCIAL
Product Image Not AvailableFor 7.5-12.5 Ton KG-KC-KH Package Units
Locke Part #: L4345MFG Part #: 54W16
ALLIED AIR COMMERCIAL
L4303.jpgGas/Electric Packaged Units
Locke Part #: L4496MFG Part #: L0915
Approvals, ETL and CSA listed, Efficiency rating verified by GAMA., Components bonded for grounding to meet safety standards for servicing required by UL., Certified in accordance with the USE certification program, which is based on ARI Standard 210/240-2006, All models are ASHRAE 90.1 compliant., All models are ENERGY STAR certified, ISO 9001 Registered manufacturing quality system., Cabinet, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Electrical and gas lines can be brought through the unit base or through horizontal access knock-outs. Optional bottom gas entry kit is available., Access panels are provided for the economizer/filter section, heating/blower section, and the compressor/controls section., Cooling system, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 f to 125 f without any additional controls., Compressor resiliently mounted on rubber grommets for quiet operation., Scroll compressors for high performance, reliability and quiet operation., Thermal expansion valve assures optimal performance throughout the application range. Removable element head., High pressure switch protects the compressor from overload conditions such as dirty condenser coils, blockedrefrigerant flow, or loss of outdoor fan operation., High capacity filter/drier protects from dirt and moisture, Freezestat protects the evaporator coil from damaging ice build-up due to conditions such as low/no air flow, or low refrigerant charge., Copper tube coil construction, enhanced rippled-edgealuminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer. Factory leak tested., Evaporator coil with cross row circuiting with rifled copper tubing optimizes both sensible and latent cooling capacity, Two independent formed condenser coils allow separation for cleaning., Plastic condensate drain pan, sloped to meet drainage requirements of ASHRAE 62.1. Side or bottom drain connections. Reversible to allow connection at back of unit., PVC coated fan guard furnished. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableHail Guard for 3, 4, 5 ton TGA, KHA, KCA
Locke Part #: L4102MFG Part #: 13R98
ALLIED AIR COMMERCIAL
Product Image Not AvailableHail Guard for 7-1/2 - 10 Ton KH
Locke Part #: L4408MFG Part #: 13T24
ALLIED AIR COMMERCIAL
Product Image Not AvailableHail Guard for TSA 072 & 090
Locke Part #: L4494MFG Part #: 13T29
ALLIED AIR COMMERCIAL
Product Image Not AvailableHail Guard for TSA 120
Locke Part #: L4495MFG Part #: 13T30
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableHorizontal Conversion Kit for TGA180
Locke Part #: L4116MFG Part #: 87M00
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableKCA180S4BN G 15 TON 460V 3PH COOL ONLY
Locke Part #: L4346MFG Part #: Z3972
ALLIED AIR COMMERCIAL
Product Image Not AvailableLGA/TGA to KGA Adapter
Locke Part #: L4475MFG Part #: 54W96
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shut-off., Heat Exchanger :, Tubular construction, aluminized steel, life cycle tested., Electronic Pilot Ignition, Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Limit Control:, Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Safety Switches:, Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant:, Non-chlorine based, ozone friendly, R-410A., High Pressure Switches, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Driers:, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil:, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer., Condensate Drain Pan:, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1, Side drain connections., Outdoor Coil Fan Motors, Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans:, PVC coated fan guard furnished., Cabinet, Construction, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited ten years aluminized heat exchanger, limited fifteen years optional stainless steel heat exchanger, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components., Approvals, AHRI Certified to AHRI Standard 340/360-2007, Units are ETL listed., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes. ALLIED AIR COMMERCIAL
Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shut-off., Heat Exchanger :, Tubular construction, aluminized steel, life cycle tested., Electronic Pilot Ignition, Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Limit Control:, Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Safety Switches:, Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant:, Non-chlorine based, ozone friendly, R-410A., High Pressure Switches, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Driers:, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil:, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer., Condensate Drain Pan:, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1, Side drain connections., Outdoor Coil Fan Motors, Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans:, PVC coated fan guard furnished., Cabinet, Construction, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited ten years aluminized heat exchanger, limited fifteen years optional stainless steel heat exchanger, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components., Approvals, AHRI Certified to AHRI Standard 340/360-2007, Units are ETL listed., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes. ALLIED AIR COMMERCIAL
Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shut-off., Heat Exchanger :, Tubular construction, aluminized steel, life cycle tested., Electronic Pilot Ignition, Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Limit Control:, Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Safety Switches:, Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant:, Non-chlorine based, ozone friendly, R-410A., High Pressure Switches, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Driers:, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil:, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer., Condensate Drain Pan:, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1, Side drain connections., Outdoor Coil Fan Motors, Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans:, PVC coated fan guard furnished., Cabinet, Construction, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited ten years aluminized heat exchanger, limited fifteen years optional stainless steel heat exchanger, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components., Approvals, AHRI Certified to AHRI Standard 340/360-2007, Units are ETL listed., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes. ALLIED AIR COMMERCIAL
Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shut-off., Heat Exchanger :, Tubular construction, aluminized steel, life cycle tested., Electronic Pilot Ignition, Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Limit Control:, Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Safety Switches:, Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant:, Non-chlorine based, ozone friendly, R-410A., High Pressure Switches, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Driers:, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil:, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer., Condensate Drain Pan:, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1, Side drain connections., Outdoor Coil Fan Motors, Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans:, PVC coated fan guard furnished., Cabinet, Construction, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited ten years aluminized heat exchanger, limited fifteen years optional stainless steel heat exchanger, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components., Approvals, AHRI Certified to AHRI Standard 340/360-2007, Units are ETL listed., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes. ALLIED AIR COMMERCIAL
Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System - Smaller, lighter condenser coil., Crankcase Heaters - Protect compressors from refrigerant liquid migration in the off cycle improving product reliability, High Pressure Switches - Protects compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Independent Outdoor Fan Motor Mounts - Allows for easy and efficient service access without removing the top panel., Constant Air Volume (CAV) or Single Zone VAV Supply Fan Blower Option - Allows constant or multi-staged air delivery, Downflow Airflow - Horizontal airflow with optional horizontal curb., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves - Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits. ALLIED AIR COMMERCIAL
Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System - Smaller, lighter condenser coil., Crankcase Heaters - Protect compressors from refrigerant liquid migration in the off cycle improving product reliability, High Pressure Switches - Protects compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Independent Outdoor Fan Motor Mounts - Allows for easy and efficient service access without removing the top panel., Constant Air Volume (CAV) or Single Zone VAV Supply Fan Blower Option - Allows constant or multi-staged air delivery, Downflow Airflow - Horizontal airflow with optional horizontal curb., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves - Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits. ALLIED AIR COMMERCIAL
Aluminized Steel Heat Exchanger With Inshot Burners - Life cycle tested., R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System - Smaller, lighter condenser coil., Crankcase Heaters - Protect compressors from refrigerant liquid migration in the off cycle improving product reliability, High Pressure Switches - Protects compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Independent Outdoor Fan Motor Mounts - Allows for easy and efficient service access without removing the top panel., Constant Air Volume (CAV) or Single Zone VAV Supply Fan Blower Option - Allows constant or multi-staged air delivery, Downflow Airflow - Horizontal airflow with optional horizontal curb., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves - Provide peak cooling performance across the entire application range., MERV 8 or MERV 13 Filters - Available as field installed option, provide an enhanced level of indoor air quality, and can help the building qualify for additional LEED credits. ALLIED AIR COMMERCIAL
R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System (All KGB Models and KGA072 and 090 Models) - Smaller, lighter condenser coil with improved heat transfer, High Pressure Switches - Protect compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Direct or Belt Drive Blower Motors - Direct drive (024, 030, 036, 048 and 060 models). Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel, Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Reversible Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves (All KGB Models and KGA036, 048 and 060 Models) - Provide peak cooling performance across the entire application range. ALLIED AIR COMMERCIAL
R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System (All KCB Models and KCA072 and 090 Models) - Smaller, lighter condenser coil with improved heat transfer, High Pressure Switches - Protect compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Direct or Belt Drive Blower Motors - Direct drive (024, 030, 036, 048 and 060 models). Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel. Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle. Corrosion-Resistant Removable, Reversible Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves (All KCB Models and KCA036, 048 and 060 Models) - Provide peak cooling performance across the entire application range. ALLIED AIR COMMERCIAL
R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System (All KGB Models and KGA072 and 090 Models) - Smaller, lighter condenser coil with improved heat transfer, High Pressure Switches - Protect compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Direct or Belt Drive Blower Motors - Direct drive (024, 030, 036, 048 and 060 models). Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel, Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Reversible Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves (All KGB Models and KGA036, 048 and 060 Models) - Provide peak cooling performance across the entire application range. ALLIED AIR COMMERCIAL
R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System (All KCB Models and KCA072 and 090 Models) - Smaller, lighter condenser coil with improved heat transfer, High Pressure Switches - Protect compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Direct or Belt Drive Blower Motors - Direct drive (024, 030, 036, 048 and 060 models). Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel. Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle. Corrosion-Resistant Removable, Reversible Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves (All KCB Models and KCA036, 048 and 060 Models) - Provide peak cooling performance across the entire application range. ALLIED AIR COMMERCIAL
R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System (All KGB Models and KGA072 and 090 Models) - Smaller, lighter condenser coil with improved heat transfer, High Pressure Switches - Protect compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Direct or Belt Drive Blower Motors - Direct drive (024, 030, 036, 048 and 060 models). Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel, Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Reversible Drain Pan - Provides application flexibility, durability and improved serviceability., Thermostatic Expansion Valves (All KGB Models and KGA036, 048 and 060 Models) - Provide peak cooling performance across the entire application range. ALLIED AIR COMMERCIAL
R-410A Refrigerant - Environmentally friendly., Scroll Compressors - Single speed scroll compressors are furnished on all models., Eco-last Coil System (All KGB Models and KGA072 and 090 Models) - Smaller, lighter condenser coil with improved heat transfer., High Pressure Switches - Protect compressor., Isolated Compressor Compartment - Allows performance check during normal compressor operation without disrupting airflow., Direct or Belt Drive Blower Motors - Direct drive (024, 030, 036, 048 and 060 models). Belt drive motors (036, 048, 060, 072 and 090 models) to maximize air performance., Independent Motor Mounts - Allows for easy and efficient service access without removing the top panel., Downflow or Horizontal Airflow - Easy field conversion., Two Fork Lift Slots on Three Sides - Easy to pick up and transport units from almost any angle., Corrosion-Resistant Removable, Reversible Drain Pan - Provides application flexibility, durability and improved Serviceability., Thermostatic Expansion Valves (All KGB Models and KGA036, 048 and 060 Models) - Provide peak cooling performance across the entire application range. ALLIED AIR COMMERCIAL
Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shut-off., Heat Exchanger :, Tubular construction, aluminized steel, life cycle tested., Electronic Pilot Ignition, Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Limit Control:, Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Safety Switches:, Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant:, Non-chlorine based, ozone friendly, R-410A., High Pressure Switches, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Driers:, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil:, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer., Condensate Drain Pan:, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1, Side drain connections., Outdoor Coil Fan Motors, Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans:, PVC coated fan guard furnished., Cabinet, Construction, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited ten years aluminized heat exchanger, limited fifteen years optional stainless steel heat exchanger, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components., Approvals, AHRI Certified to AHRI Standard 340/360-2007, Units are ETL listed., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes. ALLIED AIR COMMERCIAL
Heating System, Aluminized steel inshot burners, direct spark ignition, electronic flame sensor, combustion air inducer, redundant automatic dual stage gas valve with manual shut-off., Heat Exchanger :, Tubular construction, aluminized steel, life cycle tested., Electronic Pilot Ignition, Watchguard circuit on module automatically resets ignition controls after one hour of continuous thermostat demand after unit lockout, eliminating nuisance service calls., Limit Control:, Factory installed, limit control with fixed temperature setting. Heat limit control protects heat exchanger and other components from overheating., Safety Switches:, Flame roll-out switch, flame sensor and combustion air inducer proving switch protect system operation., Cooling System, Designed to maximize sensible and latent cooling performance at design conditions., System can operate from 30 F to 125 F without any additional controls., R-410A Refrigerant:, Non-chlorine based, ozone friendly, R-410A., High Pressure Switches, Protects the compressor from overload conditions such as dirty condenser coils, blocked refrigerant flow, or loss of outdoor fan operation., Filter/Driers:, High capacity filter/drier protects the system from dirt and moisture., Eco-last Coil System, Condenser coil features lightweight, all aluminum brazed fin construction., Constructed of three components: a flat extrusion tube, fins in-between the flat extrusion tube and two refrigerant manifolds., Evaporator Coil:, Copper tube construction, enhanced rippled-edge aluminum fins, flared shoulder tubing connections, silver soldered construction for improved heat transfer., Condensate Drain Pan:, Plastic pan, sloped to meet drainage requirements of ASHRAE 62.1, Side drain connections., Outdoor Coil Fan Motors, Thermal overload protected, totally enclosed, permanently lubricated ball bearings, shaft up, wire basket mount., Outdoor Coil Fans:, PVC coated fan guard furnished., Cabinet, Construction, Heavy-gauge steel panels and full perimeter heavy-gauge galvanized steel base rail provides structural integrity for transportation, handling, and installation., Warranty, Limited ten years aluminized heat exchanger, limited fifteen years optional stainless steel heat exchanger, Limited five years on compressors, Limited three years on the Eco-last Coil System., Limited one year all other covered components., Approvals, AHRI Certified to AHRI Standard 340/360-2007, Units are ETL listed., Components bonded for grounding to meet safety standards for servicing required by UL, ULC and National and Canadian Electrical Codes. ALLIED AIR COMMERCIAL
Product Image Not AvailableRoof Curb
Locke Part #: L4141MFG Part #: 11T96
ALLIED AIR COMMERCIAL
Product Image Not AvailableRoof Curb
Locke Part #: L4150MFG Part #: 11F59
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
L4336.jpgTAA072S4SY 6T AH 208/230V 3PH
Locke Part #: L4336MFG Part #: 45W60
APPLICATIONS, Convertible upflow or horizontal design., Each refrigerant circuit has a dedicated expansion valve., Dual distribution system for two stage capacity control during cooling cycles., Air handlers are shipped factory assembled ready to install. Standard static blower drive is furnished factory installed., REFRIGERANT SYSTEM, Multi-Circuit, Copper Tube Coil, Coils on 090-120 models are face split with separate circuits, each circuit has its own expansion valve., Coil is constructed of aluminum fins fitted to durable seamless, rifled copper tubes., Flared tubing connections and silver soldering provide tight, leakproof joints., Refrigerant Piping and Drain Connections, Refrigerant line inlets (knockouts) are provided on both sides of the cabinet., Refrigerant lines require sweat connections and are made internal to the cabinet., Condensate drain outlet extends outside the cabinet for ease of connection. Condensate drain can be relocated and repositioned., BELT DRIVE BLOWERS, Single blower wheel., Centrifugal belt driven blowers deliver large air volumes quietly and with low power consumption., Heavy-duty blower wheels, with forward curved blades and double inlet are statically and dynamically balanced., Heavy-duty bearings are permanently sealed and lubricated., CABINET, Cabinet is constructed of heavy-gauge, galvanized steel completely lined with thick fiberglass insulation for quiet and efficient operation., Drain Pan, Deep, corrosion resistant plastic drain pan. ALLIED AIR COMMERCIAL
L4336.jpgTAA090S4DG 7.5T AH 460V R410A
Locke Part #: L4338MFG Part #: TAA090S4D-G
APPLICATIONS, Convertible upflow or horizontal design., Each refrigerant circuit has a dedicated expansion valve., Dual distribution system for two stage capacity control during cooling cycles., Air handlers are shipped factory assembled ready to install. Standard static blower drive is furnished factory installed., REFRIGERANT SYSTEM, Multi-Circuit, Copper Tube Coil, Coils on 090-120 models are face split with separate circuits, each circuit has its own expansion valve., Coil is constructed of aluminum fins fitted to durable seamless, rifled copper tubes., Flared tubing connections and silver soldering provide tight, leakproof joints., Refrigerant Piping and Drain Connections, Refrigerant line inlets (knockouts) are provided on both sides of the cabinet., Refrigerant lines require sweat connections and are made internal to the cabinet., Condensate drain outlet extends outside the cabinet for ease of connection. Condensate drain can be relocated and repositioned., BELT DRIVE BLOWERS, Single blower wheel., Centrifugal belt driven blowers deliver large air volumes quietly and with low power consumption., Heavy-duty blower wheels, with forward curved blades and double inlet are statically and dynamically balanced., Heavy-duty bearings are permanently sealed and lubricated., CABINET, Cabinet is constructed of heavy-gauge, galvanized steel completely lined with thick fiberglass insulation for quiet and efficient operation., Drain Pan, Deep, corrosion resistant plastic drain pan. ALLIED AIR COMMERCIAL
L4336.jpgTAA120S4DY 10T A/H 208/230V R410A
Locke Part #: L4339MFG Part #: 45W68
APPLICATIONS, Convertible upflow or horizontal design., Each refrigerant circuit has a dedicated expansion valve., Dual distribution system for two stage capacity control during cooling cycles., Air handlers are shipped factory assembled ready to install. Standard static blower drive is furnished factory installed., REFRIGERANT SYSTEM, Multi-Circuit, Copper Tube Coil, Coils on 090-120 models are face split with separate circuits, each circuit has its own expansion valve., Coil is constructed of aluminum fins fitted to durable seamless, rifled copper tubes., Flared tubing connections and silver soldering provide tight, leakproof joints., Refrigerant Piping and Drain Connections, Refrigerant line inlets (knockouts) are provided on both sides of the cabinet., Refrigerant lines require sweat connections and are made internal to the cabinet., Condensate drain outlet extends outside the cabinet for ease of connection. Condensate drain can be relocated and repositioned., BELT DRIVE BLOWERS, Single blower wheel., Centrifugal belt driven blowers deliver large air volumes quietly and with low power consumption., Heavy-duty blower wheels, with forward curved blades and double inlet are statically and dynamically balanced., Heavy-duty bearings are permanently sealed and lubricated., CABINET, Cabinet is constructed of heavy-gauge, galvanized steel completely lined with thick fiberglass insulation for quiet and efficient operation., Drain Pan, Deep, corrosion resistant plastic drain pan. ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
Product Image Not AvailableZGB036S4BW-P 3 TON 1PH 14SEER 65K BTU GAS
Locke Part #: L9660MFG Part #: AE827
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL
ALLIED AIR COMMERCIAL